Kenmore Refrigerator 795.71073 (79571073, 795 71073) Parts

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Replace your cracked, broken, or missing refrigerator door basket. Restores secure storage for bottles, jars, and condiments on the inner door.

Refrigerator not cooling evenly or making loud noises? This evaporator fan motor circulates cold air across coils to maintain consistent temperatures.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

Front cover panel for your refrigerator door. Snaps into place to restore appearance and protect controls. Replace if cracked, broken, or missing clips.

This holder bracket secures internal refrigerator components in place. Replace if your original bracket is cracked, broken, or missing to restore stability.

This funnel assembly channels wash water inside the tub to the wash system, helping maintain proper flow and prevent internal leaks. Replace a cracked or missing funnel to restore consistent cleaning performance and reliable operation.

• Directs water flow between the tub and wash/circulation components
• Helps maintain wash pressure for effective cleaning
• Creates a proper water path at its mounting point to prevent internal leaks
• Common signs of failure: visible cracks/warping, water dripping from the area, or declining cleaning results

• Disconnect power and turn off the water supply before servicing
• Remove dish racks and interior panels/filters as needed to access the funnel location for your model
• Transfer any reusable screws, clips, or seals from the old part
• After installation, run a short cycle and check carefully for leaks

Fix loud jackhammer sounds or weak water flow from your refrigerator dispenser. This filter head assembly houses the water filter inside the fridge.

Seals the refrigerator door to keep cold air in and moisture out. Replace when worn or deformed to restore proper cooling and reduce frost buildup.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

Fix a refrigerator that won't start or hums but doesn't run with this compressor start capacitor. Restores reliable cooling when the compressor fails to start.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Door stop assembly for bottom-mount refrigerators. Mounts inside the door to control door closing and sealing. Replace if broken, cracked, or missing.

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure

Secures the hinge to your refrigerator cabinet or door. Replace this bolt if stripped, missing, or corroded to restore proper door alignment and stability.

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.