Kenmore Refrigerator 795.71302010 (79571302010, 795 71302010) Parts

This PTC cover protects the refrigerator's PTC/compressor start device from dirt, moisture and accidental contact, helping the start device operate reliably. It's a simple replacement that restores the protective enclosure for the start assembly. What it does:

• Shields the PTC/compressor start relay and wiring from debris and moisture that can cause malfunctions
• Helps prevent accidental shorting or contact with terminals during operation or service
• Can resolve symptoms where the start device is exposed or the compressor area shows visible wear or damage
• Maintains correct positioning and protection of the start components for consistent compressor starting

• One PTC cover (protective enclosure) as shown

• Disconnect power to the appliance before starting any repair
• Replace only when the start device or cover is exposed and you can access compressor/start assembly safely
• Avoid bending or stressing terminals and wiring when removing or installing the cover

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This is a replacement retaining pin used to secure small moving parts and assemblies in compatible LG appliances. It restores proper alignment and holds components in place so assemblies operate smoothly. What it does:

• Secures and locates components within an assembly to prevent shifting or disengagement
• Helps maintain proper alignment for moving parts that can cause noise or malfunction when loose
• Commonly used where a small, durable metal pin is needed to retain clips, levers, or linkages
• Simple, single-purpose part — replacement when the original is bent, worn, or missing

• One retaining pin

• Unplug the appliance or disconnect power before servicing
• Access the affected assembly per the appliance service instructions; small fasteners or clips may need removal
• Use pliers or appropriate hand tools to remove/install the pin; avoid forcing to prevent damage
• Keep track of orientation and any associated clips or washers during disassembly

This door stopper cushions and limits an appliance door's travel to prevent slamming and reduce wear on the hinge. It helps the door close smoothly and reduces noise for a better user experience. What it does

• Stops and cushions the door at the end of its swing to prevent hard impacts
• Reduces hinge and cabinet wear caused by repeated slamming
• Helps eliminate banging or rattling noises during door movement
• Can restore proper door feel when the original stopper is cracked, worn, or missing

• One door stopper

• Service with the appliance unplugged and/or power disconnected for safety
• Typically installed at the hinge/cabinet area using basic hand tools; may require removing a trim or access panel
• Inspect hinge screws and mounting area; replace any damaged hardware and tighten to secure the stopper

This replacement door shelf bar secures items on a refrigerator door shelf, restoring proper storage and helping keep bottles and containers from sliding or falling when the door is opened. A simple, direct fix for broken or missing shelf retainers. What it does

• Holds door-bin items in place so bottles, jars and containers stay secure during normal use
• Replaces cracked, warped or missing shelf retainer bars that allow items to tip or fall
• Helps restore proper shelf function and usable door storage
• Designed to match the OEM fit and mounting points for a direct replacement

• Remove contents from the door shelf before replacing the bar
• Install by aligning with the shelf slots or mounting tabs and snapping or sliding into place per the original orientation
• Use gentle pressure to avoid damaging surrounding bins or trim; do not force metal parts
• Refer to your refrigerator's owner's manual for model-specific instructions and safety guidance

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This is the ice bucket that stores ice dispensed by your refrigerator's ice maker. A cracked, warped, or stuck bin can jam the auger or spill ice, leading to poor dispensing and messy freezers.

• Holds and dispenses harvested ice from the ice maker to the door chute or bin access
• Common failure signs: cracked bucket, ice not dispensing, auger not turning, ice clumping or spilling
• Restores smooth ice dispensing and proper storage in the freezer
• Built to fit the original mounting and drive interface for an easy swap

• Unplug the refrigerator and wear cut-resistant gloves
• Remove the old bin carefully; thaw any ice buildup before transferring
• Inspect the auger drive coupling for wear before installing the new bucket
• Seat the bucket fully so the drive engages; test dispense with a small amount of ice

This connector secures and transmits motion between the drawer drive and the sliding assembly, restoring smooth drawer movement and alignment. It's a direct-fit replacement that helps fix sticking, slipping, or non-moving drawers. What it does:

• Couples the drawer drive mechanism to the sliding gear, allowing the drawer to open and close reliably
• Replaces worn or broken connector teeth or mounts that cause skipping or jammed operation
• Helps correct uneven or noisy drawer movement caused by damaged linkage
• Restores proper engagement so the drawer responds to normal open/close controls

• One connector as shown

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Inspect surrounding gears, tracks, and mounting points; replace any damaged parts for best results
• Basic hand tools are typically required; handle plastic gears carefully to avoid further damage

This replacement cover is an exterior access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and mechanisms enclosed while maintaining the cabinet's original look. What it does:

• Covers and protects internal components from dust, spills, and accidental contact
• Restores the appliance's cosmetic appearance when the original cover is cracked, chipped, or missing
• Helps maintain proper airflow routing and component spacing behind the panel
• Prevents small objects from entering service areas that could cause damage

• One replacement cover

• Disconnect power and water before starting any repair
• Remove fasteners or release retaining clips holding the old cover; keep hardware if re-using
• Align the new cover carefully and secure with the original screws or clips; do not force into place
• If clips or mount points are damaged, replace them before finishing installation

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary