Kenmore Refrigerator 795.75194401 (79575194401, 795 75194401) Parts

Protects refrigerator light bulbs and sockets from moisture and impacts. Replace if cracked, melted from bulbs staying on, or discolored. Confirm fit.

Drier assembly for refrigerators. Installs in the sealed refrigerant system to remove moisture and contaminants. Replace if damaged or worn during repair.

Replace a cracked, split, or leaking 1/4" water supply tube in your refrigerator. Connects household water line to dispenser and ice maker system.

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

Refrigerator not cooling properly or compressor overheating? This condenser fan assembly circulates air across coils to restore efficient cooling performance.

This DC fan motor drives the refrigerator's fan to circulate air across the coils and through the cabinet. Replacing a weak or failed motor restores proper airflow for consistent temperatures and reliable cooling performance.

• Spins the fan blade to move air through the cabinet and across heat-exchange coils
• Helps maintain even, stable temperatures throughout the appliance
• Typical failure symptoms: fan not running or intermittent, unusual humming/squealing/rattling near the fan area, poor cooling or temperature fluctuations
• Can reduce hot spots by restoring proper air circulation

• Disconnect power before servicing; use cut-resistant gloves
• Access the motor behind the rear cover or interior panel (location varies by model)
• Note connector orientation; disconnect harness, mount the new motor, and securely route wiring
• Ensure the blade spins freely with no obstructions; restore power and verify fan operation

Right side upper hinge.

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

This supporter, holder is the small interior bracket that secures its matching holder/assembly inside your refrigerator. Replace a cracked or missing support to restore a solid, level fit and keep the component from wobbling or dropping.

• Provides structural support for the designated holder/assembly inside the fresh food compartment
• Keeps the component aligned so shelves/covers/bins sit level and operate smoothly
• Direct replacement for a broken, warped, or missing support
• Typical symptoms include: holder won't stay attached, tilting or sagging, rattling when doors close, visible cracks or stripped tabs

• Disconnect power to the refrigerator before servicing
• Remove the item the support holds (such as the related shelf, cover, or bin)
• Release locking tabs and/or remove screws; transfer any reusable hardware
• Align and snap or screw the new support into place, then reinstall the component and verify a secure fit

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Mounts behind the interior light to direct and spread illumination. Replace if cracked, melted, warped, or missing to restore bright, even lighting.

Ice maker not getting water or refrigerator not filling? This water inlet valve controls water flow to your appliance. Moderate DIY repair in 30-45 minutes.

Replaces broken or missing refrigerator door stop. Limits door travel to prevent over-extension and maintain proper alignment and smooth operation.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Secures panels, brackets, and trim components inside your refrigerator. Replace this fastener if it's stripped, lost, or damaged to restore alignment.