Kenmore Dryer 796.90441900 (79690441900, 796 90441900) Parts

Dryer won't heat or stops mid-cycle? This gas burner valve assembly controls fuel flow to the igniter. Moderately challenging repair with basic tools.

This washer tub assembly is the stationary outer tub that surrounds the spin basket and contains the wash water. Replacing a cracked or damaged tub helps stop leaks and restores proper clearance for smooth, quiet washing and spinning.

• Creates a watertight chamber around the basket to hold wash and rinse water
• Maintains proper basket clearance; damage can cause rubbing or scraping sounds
• Provides connection points for hoses and water-level components
• Common signs it may be needed: leaks from the tub area, visible cracks or warping, persistent out-of-balance/spin errors, or internal scraping/grinding noises

• Disconnect power and water; shut off supplies and safely drain remaining water
• This is a major repair—allow time and consider a second person to help lift/support the tub
• Transfer model-specific parts from the original tub to the new tub as needed; reinstall all clamps, bolts, and sensors securely
• After reassembly, level the washer, and run a test cycle to check for leaks

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This is the front bulkhead panel that forms the front wall of the dryer drum opening. It provides structural support for the drum and typically includes the felt seal and bearing surfaces that allow the drum to rotate smoothly. Replace this assembly if the front panel is cracked, warped, or worn, or if you notice excessive noise, drum wobble, or clothes getting caught between the drum and the front panel.

Metal mounting bracket that secures internal dryer components to the frame. Replace if cracked, bent, or broken to restore proper alignment and stability.

Base bracket for dryer installation and structural support. Replace if your original bracket is cracked, broken, bent, or missing to restore proper stability.

Mounting bracket that secures internal dryer components. Replace if cracked, broken, or missing to restore proper alignment and stability of assemblies.

Dryer duct assembly that connects the drum to the blower housing. Replace if cracked, damaged, or has torn foam seals around openings.

This power cord assembly supplies AC power to the appliance and restores safe operation after a damaged or faulty cord. It replaces the worn or frayed factory cord so the appliance can power on reliably. What it does

• Provides the main AC connection between the appliance and household power
• Replaces cords with visible damage, exposed wiring, burnt connectors, or intermittent power
• Helps stop arcing, sparking, or overheating caused by a failing cord
• Fits into the appliance's cord terminal block for a direct, plug-in power connection

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Tighten all terminal screws securely and route the cord away from sharp edges and moving parts

Wire harness for dryers. Connects electrical components inside the cabinet. Replace if wires are frayed, damaged, or connectors are broken or melted.

This dryer vent hose connects your dryer to the exhaust vent. Replace if cracked, torn, kinked, or showing wear that restricts airflow and lint removal.

This generator assembly senses motor rotation and provides the control board with speed/position feedback so the washer can time cycles and spin properly. It replaces a worn or damaged sensor assembly to restore reliable cycle control. What it does:

• Detects motor rotation and sends position/speed signals to the washer control board
• Helps the machine maintain correct spin speeds and cycle timing
• Can address symptoms like no spin, erratic spinning, or motor-related error codes when the generator fails
• Works with the motor/mounting components to ensure accurate feedback for drive operations

• One generator assembly

• Disconnect power before servicing to avoid shock or injury
• Requires basic tools and access to the washer's motor area; handle connectors and sensor surfaces carefully
• Reuse or replace any mounting hardware only if specified by the manufacturer

Inner door frame for dryers. Secures the door glass and outer panel assembly. Replace if cracked, warped, or broken to restore door structure and seal.

Base bracket for dryers. Mounts to the bottom of the cabinet to secure the base assembly. Replace if bracket is cracked, bent, or missing hardware.