Kenmore Washer 970.-C40052-00 (970-C40052-00, 970 -C40052-00) Parts

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

Includes bearing and seal. Bearing is not available separately.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

This is a motor-mount screw used to secure the appliance motor housing. It's a direct-fit fastener that restores proper motor attachment to reduce movement and rattling caused by loose or missing hardware. What it does:

• Secures the motor to its mounting bracket or housing
• Prevents motor shifting that can cause vibration, noise, or misalignment
• Restores proper mechanical connection after strip-out or lost hardware
• Helps maintain safe operation by keeping motor fastened

• Disconnect power before servicing the appliance.
• Use the correct screwdriver or socket to avoid stripping the head.
• Thread carefully and tighten to snug; avoid over-tightening which can strip threads.
• If mounting holes or threads are damaged, repair or replace the affected components before reinstalling.

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks