Kenmore Washer Dryer Combo 970.-C98902-00 (970-C98902-00, 970 -C98902-00) Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 131461200
The Washer Drain Hose is an OEM replacement part for Frigidaire washing machines. It is a flexible, 7 ½ ft plastic hose that connects the washer tub to the household drainage system. The drain hose removes water from the washer at the end of each cycle.
Symptoms of a faulty drain hose include:
- Water failing to fully drain or continuously draining
- Wet flooring around the washer due to leaks
- Excess water left standing in the washer tub after cycles
- Reduced washing performance due to inadequate drainage
Causes of a bad drain hose include kinks or bends that restrict water flow, cracks or holes from wear and tear, and blockages from accumulated debris. These issues can compromise the hose's ability to drain water properly.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaky drain hose Rocco S. • Rochester , NY • February 24, 2017
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day!
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134418700
The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.
Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.
Symptoms of a bad agitator hub include:
- Agitator not moving or rotating properly
- Loud noises or grinding sounds during the wash cycle
- Clothes not being cleaned effectively
- The washer shaking or vibrating excessively
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The agitator was not working John H. • Auburn , NY • October 11, 2016
The agitator stopped functioning and there was a squeaking sound occurring in agitation mode. I found that if I cranked down on the agitator cap, screwing in as hard as I could, the agitator would work briefly, then the cap would loosen and agitator stop moving. I removed the agitator cap, along with which came the agitator stud cap and a rubber washer/seal which was jammed up into the underside of the cap. I lifted out the agitator from the drum and inspected it and the hub best I could....
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131862900
The Idler Pulley is an OEM part for Frigidaire dryers. It helps guide and maintain tension on the dryer drum belt, ensuring the drum rotates smoothly during the drying cycle.
Over time, the idler pulley can wear out due to friction and regular use, or it may become damaged from excessive strain or misalignment. If the idler pulley fails, the dryer drum may not rotate properly, leading to inefficient drying or a complete inability to dry clothes.
Symptoms of a bad Idler Pulley include:
- Squeaking or squealing noises during operation
- The drum not rotating or rotating unevenly
- The belt appearing loose or slipping off the drum
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131545101
The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:
- Secures and centers the spin basket on the drive shaft for balanced rotation
- Transfers drive torque to the inner tub during spin
- Helps maintain basket alignment to reduce vibration
- Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events
What's included:
Install notes:
- Disconnect power and water before service; wear gloves and eye protection
- Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
- Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
- Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin
Do-It-Yourself Stories from Customers like You
Leaking washer tub Hugh S. • Miami , FL • June 25, 2016
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134737100
This gear assembly transfers power from your washer's motor to the agitator and spin basket. It controls the different motions needed for washing and spinning cycles. Replace it if your washer agitator doesn't move, makes loud grinding noises, or fails to spin clothes dry.
Do-It-Yourself Stories from Customers like You
Deffective transmission bearing at the bottom Warren G. • Queens Village , NY • April 13, 2016
Replace with a new assy
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131658100
Do-It-Yourself Stories from Customers like You
Dryer had stopped heating Ron B. • Saint Augustine , FL • June 29, 2018
Replaced the dryer heater, and for good measure the limit and thermostat switches.
My whole experience with Appliance Parts Pros was exceptional. I had a few questions to which the pros went out of there way to get the answers I needed. They also sent me the service manual which had step by step illustrations on how to disassemble the dryer. Saved a lot of time.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 3204394
Do-It-Yourself Stories from Customers like You
Missing bleach dispenser. Jim W. • Ardmore , OK • May 12, 2020
Ordered part.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303208586
This terminal block screw secures the power cord leads to the appliance's terminal block, helping maintain a tight, reliable electrical connection. Replace missing, stripped, or heat-damaged screws to restore proper clamping of the wire lugs.
- Clamps incoming power wires to the terminal block for a secure electrical connection
- Replaces stripped, corroded, or missing terminal screw
- Designed to fit the original terminal block hardware locations
What's included: 1 terminal block screw Install notes:
- Disconnect power at the breaker or unplug the appliance before servicing
- Access the terminal block (location varies by model); note wire positions
- Inspect terminal block and wire lugs; replace any heat-damaged components
- Install and tighten the new screw securely without over-tightening; reinstall access cover and verify strain relief is in place before restoring power
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134101800
This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.
Do-It-Yourself Stories from Customers like You
My 20 year old frigidaire stackable washer needed the lid switch replaced so it would trigger the spin cycle Maryann S. • Owosso , MI • March 13, 2014
I unplugged the power source to the appliance. I unscrewed 2 screws and unplugged the lid switch.
I replaced the old switch with the new switch and screwed in the same 2 screws that held the old
switch in place and plugged the new lid switch back in under the lid. that's it . I plugged in the washer
and started a load of clothes. works just fine. NO HUGE REPAIR BILL. Gosh it makes me happy to
do such a simple repair to my old machine and for a very reasonable part price, my washer is...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134192400
Genuine Frigidaire part
By: Frigidaire
Part Number: 134446800
The dryer timer power resistor regulates electrical current to the timer motor in mechanical timer systems. Replace when the timer fails to advance properly, gets stuck in cycles, or the dryer runs continuously without stopping.
Do-It-Yourself Stories from Customers like You
Dryer timer would not advance in automatic dry mode worked fine in timed mode Michael S. • Bear , DE • February 05, 2016
Replaced the power resistor on the timer assembly. Solved the problem.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131063700
Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131104303
Genuine Frigidaire part
By: Frigidaire
Part Number: 131221310
Genuine Frigidaire part
By: Frigidaire
Part Number: 131288101
Genuine Frigidaire part
By: Frigidaire
Part Number: 131288211
White. Right hand side
Do-It-Yourself Stories from Customers like You
Washer wouldn't run but as dryer did it obviously wasn't a circuit breaker E James W. • Wilmington , NC • September 29, 2014
First attempt was to replace the door latch mechanism...didn't fix it.
Kept researching and the washer control knob had been hard to turn so it seemed logical that was the problem. Also, at some point the end cap had broken. As it has the main grounding point inside it and as I was taking the control panel apart anyway it made sense to replace it.
Read more
More