Lg Refrigerator 71029 Parts

Replace your refrigerator's LED light assembly when lights flicker, dim, or fail. Restores bright, energy-efficient interior lighting. Verify fit by model.

Plastic tube that routes water between internal refrigerator components. Replace if cracked, kinked, leaking, or brittle to restore water flow.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Right side upper hinge.

Covers and protects the interior compartment fan while directing airflow. Replace if cracked, broken, or missing to restore safe air circulation.

This fan blade attaches to the condenser fan motor located near the bottom rear of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigeration system running efficiently. Replace this blade if it is cracked, warped, or broken, which can cause loud noises, poor cooling performance, or the compressor overheating and shutting off.

This joint assembly is the connector that joins two refrigerator water tubes to form a tight, leak-resistant seal. Replace it to stop leaks at a line coupling and restore reliable dispenser and icemaker water flow.

• Connects two plastic water lines within the refrigerator's water system
• Maintains a watertight seal to prevent drips and air intrusion
• Common fix for leaks at a coupling or tubing that won't stay seated
• Symptoms include slow/sputtering dispenser, small/no ice production, or visible seepage at the connector

• Unplug the refrigerator and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Depress the connector collar to release the tubing; cut damaged tube ends square and fully insert tubing until it bottoms out
• Restore water and power, then check all connections for leaks

Refrigerator not cooling properly or showing temperature errors? This temperature sensor monitors compartment temps and sends readings to the control board.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Replacement ice bucket that collects and stores ice in your refrigerator's freezer. Molded plastic bin prevents spills and keeps ice organized.

Secures and guides your refrigerator door for smooth opening and closing. Replace if door sags, rubs, or won't seal properly. Confirm fit by model number.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.