Lg Range 76037 Parts

Note: This glass is "approximately" 11"tall x 20"wide.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

Fix weak or uneven flames on your gas cooktop with this surface burner assembly. Restores consistent heat and proper flame pattern for cooking.

Replace a cracked or broken oven door hinge bracket on your electric range. Secures the door hinge mechanism to the frame for proper door alignment.

This is the orifice holder that sits beneath the surface burner on a gas range, securing the gas orifice in position so fuel is directed properly to the burner head. It ensures a consistent and correctly shaped flame for even cooking. Replace this part if you notice irregular flame patterns, difficulty igniting a burner, or if the orifice is loose or misaligned.

If your gas range burner won't light or produces uneven flames, this surface burner assembly restores proper ignition and even heat distribution.

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

Seals your gas range oven door to prevent heat loss and maintain even cooking. Replace if worn, cracked, or door won't seal properly. Verify fit.

This Knob Assembly replaces a worn or broken control knob so you can select cycles and settings accurately. It restores a positive grip and smooth rotation for reliable control of the appliance. What it does:

• Allows selection of functions, cycles, or temperature settings on the control panel
• Replaces stripped, cracked, or loose knobs that no longer turn or click into position
• Restores tactile feedback and improves control accuracy
• Helps eliminate slipping or intermittent contact between the user and the control shaft

• One Knob Assembly as shown

• Disconnect power before beginning any repair to avoid shock or injury
• Pull off the old knob by hand; align and press the new knob onto the control shaft until it seats
• If the knob is secured with a set screw, loosen/tighten with the proper screwdriver — do not overtighten

This is a VFD (vacuum fluorescent display) module that mounts behind the range's control panel and shows time, temperature, error codes, and cycle status. It communicates with the main electronic control board to relay information to the user. Replace this display board if the screen is blank, dim, flickering, showing incomplete characters, or displaying incorrect information even after a power reset.

This is a metal base panel that sits at the bottom of the upper oven cavity in a range. It serves as a heat shield and floor surface, protecting the lower cabinet structure from direct heat exposure while helping distribute heat evenly. Replace this panel if it is warped, rusted, or has holes that allow grease and food debris to fall into the lower compartment.

Base plate for electric and gas ranges. Provides structural support at the bottom of the range. Replace if cracked, warped, or damaged from wear.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

Replacement mounting screw for electric and gas ranges. Secures components and panels. Needed when original screw is stripped, missing, or damaged.

This is a wire holder clip used inside a microwave to secure and route internal wiring. It keeps wires organized and safely positioned away from heat sources and moving components. Replace this holder if it is broken or missing, which can allow wires to hang loose and potentially contact hot surfaces or interfere with other parts.