Lg Washer 79641073311 Parts

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

Water inlet hose that connects your washer to the water supply. Replace if cracked, leaking, or worn to prevent water seepage around your appliance.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

Machine screw that fastens brackets, panels, or housings in select washers. Replace when missing, stripped, or damaged to restore secure assembly fit.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Fix washer leaks or no water flow with this water inlet connector hose. Routes water from valve to dispenser. Direct-fit replacement for worn hoses.

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Replacement door handle for washer. Restores secure grip and factory appearance. Replaces cracked, loose, worn, or broken handles for smooth opening.

Fix water leaking from your washer dispenser or misdirected flow with this dispenser water guide channel. Routes water properly to prevent splashing.

Replacement drawer support lifter for washers. Holds and guides the drawer for smooth operation. Replace if cracked, broken, or causing uneven movement.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Fix washer not filling or slow fill issues with a new water inlet hose. Connects your water supply to the fill valve. Easy 15-minute repair.