Lg Washer 79641073311 Parts

My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more

I suspected the tub gears where ready to break so I dismantled my LG WM2032HW front load washer. I found the spyder gear corroded and broken. I also found that the stainless steel drum abraded the front tub cover so bad, it was cracked. My washer is an early model and always had standing water in the door seal after a wash. What I learned is LG stopped making the orginal front tub cover and replaced it with one that had a drain hole at the bottom front edge. I also learned that this new... Read more

The husband fixed the problem. Took the washer apart and replaced the Stator Assembly. Read more

The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more

Watched videos ordered all the parts that could possibly cause this problem. We changed the shock absorpers, springs and air chamber. putting the pins back in the shock absorbers was a challenge you need to have a lot of strength to get them back in. The huge problem we had was that one of the screws on the front panel was rusted, we could not get it out had to drill out the screw that took forever, Tools used were screw gun, spring tool, pliers, and channel Locks, screw driver, socket Read more

I looked online ans read where the tE error code meant the thermistor was bad. I then found a video on YouTube showing how to replace the part. On AppliancePartsPros.com I chatted with a technician that told me the thermistor on my particular model was built into the heater unit and he gave me the link to purchase it. After it arrived via FedEx I followed the repair video and installed it myself (I'm a girl). So far I have run about a half dozen loads and no problems! Thank you so much... Read more

I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more

After doing a little research it seemed likely that our 7 year old LG's suspension system was getting old. We're getting very loud sounds on our spin cycle. A lot of start-up of spin and then stopping to rebalance occurring within the machine and intermittent unbalanced load error where the machine stopped the cycle completely to display an error. We replaced all three shock absorbers and the two suspension springs and our washer is back to what seems like better than new. Quieter with... Read more

Bought the part that doesn’t have a picture to it and it wasn’t quite the one I needed, but it worked so all in all it was an easy repair. Read more

The dealer gave us a door but it didn't fit. Everything we bought from Appliance Parts Pros.com was fixed with just a screwdriver. Easy and fast. Shipping was fast also. The longest time was installing the hinges on a stacked washer and dryer. Read more

I went to your web site found the part using the model number of the washer machine. Also with the part picture, there was a video showing step by step instructions. They were very clear and was breeze replacing the hose.Doing this myself saved at least probably $150-200. Appliance repair shops quoted me around $80.00 just to come out. Then they mark up the price of the hose at least twice the cost of what I paid , They too have to order the part and come back to install. So the labor was what... Read more

Following what I've seen or watched from you tube video clinic "how to replace drain pump for LG Washer, model wm2277hw and the help that I received from representative/ customer service of appliacepartspros, I fixed our LG Washer no problem. I am very much thankful to the representative of AppliacePartsPros who help me analyzed the problem and recommended the right parts that I needed and most importantly arrived 2 days as ordered. I would recommend AppliacePartsPros for ordering your parts. Read more

Replaced the drain pump and circulating pump units. Read more