Lg Dryer 79661552610 Parts

Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.

This is a mounting holder or grille that secures the moisture sensor bars inside the dryer drum area. The moisture sensor detects how wet the clothes are and signals the control board to end the cycle when they're dry. Replace this holder if it is cracked, broken, or missing, which can cause the sensor bars to be misaligned and lead to clothes coming out still damp or the dryer running too long.

Stationary platform that sits inside the dryer drum to hold shoes, delicates, and other items in place during air drying. Replaces damaged or missing racks.

Distortion spring that applies tension within the dryer mechanism. Replace if fatigued, broken, or missing to restore proper tension and assembly function.

Replacement filter cover that secures your dryer's lint filter inside its housing. Installs quickly to replace a cracked, broken, or missing cover.

This is a fastener and retainer assembly that secures the blower wheel to the motor shaft inside a dryer. It keeps the blower wheel firmly in place so it can properly circulate hot air through the drum and out the exhaust vent. Replace this assembly if the blower wheel wobbles, makes rattling or squealing noises, or if the retainer nut is stripped or broken, causing poor airflow and longer drying times.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Fix a dryer door that won't stay closed or pops open with a new door hinge. Restores smooth pivoting and proper alignment. Basic DIY repair.

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

Secures brackets, panels, and covers on your dryer. Replace missing, stripped, or damaged screws to keep components aligned and prevent rattling.

Dryer door sagging, rubbing, or won't close properly? This door hinge restores smooth opening and secure latching. Straightforward 15-minute fix.

Hardware screws and nuts for installing a dryer side vent kit. Replace missing or stripped fasteners when reconfiguring exhaust outlet direction.

This hinge assembly mounts the dryer door to the front panel of the dryer, allowing it to open and close smoothly. It consists of the hinge bracket and pin mechanism that supports the weight of the door. Replace this assembly if your dryer door sags, won't stay closed, or if the hinge is visibly bent, cracked, or worn.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

This inlet hose carries water from your home's supply line into the appliance. Replacing a cracked, kinked, or leaking hose restores proper water flow and helps prevent leaks and fill-related errors.

• Connects the household water supply to the unit's fill circuit
• Provides a sealed path for incoming water
• Damage can cause leaks, restricted flow, or fill errors
• Common signs: slow/no fill, visible leaks, kinks, bulges, or brittle tubing

• Unplug the appliance and turn off the water supply before service.
• Place a towel or pan to catch residual water; relieve line pressure before disconnecting.
• Route the new hose without sharp bends; hand-start threads, then snug—do not overtighten.
• Restore water and power; check all connections for leaks.