Lg Dryer 79661552610 Parts

This hinge assembly mounts the dryer door to the front panel of the dryer, allowing it to open and close smoothly. It consists of the hinge bracket and pin mechanism that supports the weight of the door. Replace this assembly if your dryer door sags, won't stay closed, or if the hinge is visibly bent, cracked, or worn.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Precision mounting screw for dryers and laundry centers. Replaces missing, stripped, or damaged screws that secure panels, brackets, and assemblies. Restores stability.

Dryer won't start or stops mid-cycle? This door strike hook secures the door latch, engaging the switch so cycles can begin and run properly.

Fix a dryer door that won't stay closed or latched with this door lock assembly. Restores secure door closure for safe operation. Simple DIY repair.

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

This inlet hose carries water from your home's supply line into the appliance. Replacing a cracked, kinked, or leaking hose restores proper water flow and helps prevent leaks and fill-related errors.

• Connects the household water supply to the unit's fill circuit
• Provides a sealed path for incoming water
• Damage can cause leaks, restricted flow, or fill errors
• Common signs: slow/no fill, visible leaks, kinks, bulges, or brittle tubing

• Unplug the appliance and turn off the water supply before service.
• Place a towel or pan to catch residual water; relieve line pressure before disconnecting.
• Route the new hose without sharp bends; hand-start threads, then snug—do not overtighten.
• Restore water and power; check all connections for leaks.

This side vent hole cover seals unused ventilation openings in your dryer cabinet. It prevents lint buildup and maintains proper airflow through the designated exhaust path. Install this cover if you have an open hole causing lint to escape into areas where it shouldn't or affecting drying efficiency.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

Mounting bracket that secures and stabilizes the dryer door hinge assembly. Replace if cracked, broken, or causing door misalignment and sagging.

This is a door lock and switch assembly that secures the washer door during operation and signals the control board that the door is properly closed. It prevents the door from being opened while the drum is spinning and allows the wash cycle to begin. Replace this assembly if the washer won't start, displays a door lock error code, the door won't lock or unlock, or the cycle stops unexpectedly.

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Dryer not heating or taking too long to dry? This heating element restores proper heat generation. Moderate DIY repair solves no-heat issues fast.