Lg Dryer 79661552610 Parts

This upper plate clip secures the control panel assembly to the top of the dryer cabinet, keeping it properly aligned and firmly in place. It is a small but important mounting component that prevents the control panel from shifting or becoming loose during operation. Replace if the clip is broken or missing and the control panel feels wobbly, does not sit flush, or has become detached.

Vertical connector bar for dryer drum assembly. Replace if cracked, bent, or broken. Structural part that connects vertical components inside cabinet.

This gasket creates an airtight seal between the dryer door and the drum opening to keep heated air inside the drum during operation. It is typically made of flexible felt or rubber and mounts around the door or the front of the tub. Replace this seal if you notice heat escaping around the door, longer drying times, or visible wear, tears, or hardening of the gasket material.

This kit includes the high limit thermostat and thermal cut-off fuse that protect the dryer from overheating. The thermostat monitors the exhaust temperature and shuts off the heating element if it gets too hot, while the thermal fuse acts as a one-time safety device that permanently breaks the circuit during a dangerous overheat condition. Replace these components if the dryer won't heat, shuts off prematurely, or won't start at all - a blown thermal fuse is a common cause of a completely non-functional dryer.

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

Secures the door hinge to your dryer cabinet for proper alignment and smooth operation. Replace if the door sags, rubs, or won't stay open. Confirm fit with your model number.

This is a damper mechanism attached to the dryer door hinge that controls how the door opens and closes. It provides resistance so the door doesn't swing open too quickly or slam shut. Replace this assembly if the dryer door swings open uncontrollably, won't stay closed, or the damper no longer provides smooth resistance when opening or closing.

This handle assembly replaces a worn, cracked or broken refrigerator door handle to restore a secure grip and smooth door operation. Designed to mount in the factory handle location for a clean, factory appearance. What it does

• Provides a finished grip surface for opening and closing the refrigerator door.
• Replaces damaged or loosened handles that can catch, wobble, or separate from the door.
• Helps prevent cabinet and door edge damage caused by attempting to open with a compromised handle.
• Matches the factory fit and mounting points for straightforward replacement when compatible.

• Disconnect power to the appliance and remove food/items from the door area before beginning work.
• Support the door while removing fasteners; some models use hidden screws or trim pieces—retain all hardware.
• Use common hand tools and avoid over-tightening fasteners to prevent handle or door damage.

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This connector nozzle attaches to the appliance's nozzle assembly to route fluid through the system and help maintain a sealed connection. It replaces a worn or cracked nozzle connector to restore proper flow and reduce leaks. What it does:

• Provides a secure connection point for the nozzle assembly, directing fluid through the correct pathway
• Restores a sealed joint to prevent drips or steady leaks at the nozzle area
• Helps eliminate flow interruptions caused by a cracked, split, or damaged connector
• Works as a direct-fit replacement when the original connector is broken or degraded

• One connector nozzle

• Turn off power and shut off the water supply before starting any repair
• Remove only the components necessary to access the nozzle area; use basic hand tools
• Check seals and adjoining hoses for wear and replace if needed to ensure a leak-free connection

Secures the dryer door hinge to the cabinet frame. Replace this mounting bracket if it's cracked, broken, or worn to restore proper door alignment.

Fix a dryer that won't start, stops mid-cycle, or has intermittent power issues with this wire harness. Connects electrical components. Moderate DIY repair.

Secures the door hinge assembly to the cabinet for proper door support and alignment. Replace when the hinge area is cracked, worn, or damaged.

This replacement locker handle restores a secure grip and reliable latch operation on the appliance door or access panel. It replaces a cracked, loose, or missing handle so the door opens and closes smoothly. What it does:

• Provides a firm handhold for opening and closing the door or access panel
• Secures the door latch area to help maintain proper closure
• Replaces broken, cracked, or worn handles that are hard to grip
• Helps reduce rattling or loose-feeling door operation

• One locker handle

• Disconnect power to the appliance before beginning any repair
• Remove any trim or access panels as needed; use basic hand tools
• Handle may attach with clips or screws — keep hardware organized for reassembly
• Test door operation after installation; if fit feels incorrect, check part number and orientation