Lg Washer WD-10190BD Parts
Genuine Lg part
By: Lg
Part Number: 4811ER3001A
Do-It-Yourself Stories from Customers like You
Ue error code just before going into spin cycle on my lg tromm front load washer model wm2077 Richard B. • Cheshire , CT • September 07, 2014
Replace the ball sensor. Also known as the out of balance sensor .
Another confirmatory clue was when I ran the QC diagnostics . The moment I ran the first diagnostic test, the spin test, I got a bE (ball sensor) error code in the display and the drum would rotate slowly. When I replaced the sensor the drum ran at very hig speed the moment I entered the diagnostic. This was a good way to confirm in a few seconds that the sensor fixed the problem without having to run a wash load and waiting...
Read more
More
Genuine Lg part
By: Lg
Part Number: 4986ER0001C
This seal has a drain hole. If your model does not have a drain hole, order part# 4986ER0001A.
Do-It-Yourself Stories from Customers like You
Leaking door boot seal Mark T. • Cedar Falls , IA • December 13, 2019
Replaced the seal. Washer didn’t have a drain hole and this seal is no longer available. So I ordered the seal with a drain hole. The seal fits perfectly but I had to make a plug and use silicone to plug the drain hole.
Read more
More
Genuine Lg part
By: Lg
Part Number: 5220FR2008C
This water inlet valve is a genuine OEM replacement part that is sourced directly from the manufacturer for use in washing machines. The water inlet valve is the gatekeeper for the water flow into the washer. When the operator sets the wash cycle, the solenoid fires up and tells the valve to open the gate for hot or cold water or both to fill the washer tub. When the tub has filled to a preset level, the valve gates close and the water flow stops. If this valve fails, the water will not stop and will eventually flood or the water might not be signaled to flow at all. This repair requires a Phillips screwdriver and pliers. Disconnect the power source and turn the water off before working on the washing machine. Remove the back panel from the washer and locate the inlet valve. Disconnect the hoses from the valve. Remove the damaged valve. Install the new inlet valve. Connect the hoses in the same order they were removed and put the back panel on the washer. Reconnect the water and power.This water inlet valve is made of molded plastic and is individually sold. It does not include screws. It is made specifically for washing machines manufactured by LG.
Do-It-Yourself Stories from Customers like You
FE Error on LG WM0532HW Curt H. • Covington , KY • March 12, 2014
I found other posts on AppliancePartsPros.com to be helpful. Most people and pros indicated that it was the Cold Water intake valve which has 4 solenoids on it. I watched the video to replace the Hot Water valve which is right next to it. My washer opened differently than the one in the video but it was not hard to figure out. Tools needed; Philips screwdriver and pair of regular pliers. I took the screws off of the small panel on top on the back of the washer. This allowed the control...
Read more
More
Genuine Lg part
By: Lg
Part Number: 3045ER1006E
Do-It-Yourself Stories from Customers like You
Growling noise coming from the rear of the drum of my lg wm0642hw front load washing machine Lydia F. • Willimantic , CT • June 07, 2016
I followed the video that was posted on your website, very informative and easy to follow. Only problem was, was the drum and bearings refused to separate, even after a week of applying rust buster and using a 5 lb sledge hammer and 2x4 wood. Spoke with one of your exceedingly helpful assistants on the phone and he gave me the only other option was to replace the rear drum assembly and the inner drum.
So easy!!
It's back together and running! I now can revel in clean laundry!
I only have...
Read more
More