Lg Washer WM2301HS Parts

Supports the washer drum for smooth, quiet spinning. Replace if you hear grinding noises or excessive vibration during cycles. Confirm fit with your model.

Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.

Locking pin for shock absorber.

Replacement wire harness for washers. Restores electrical connections between components when original wiring is damaged, frayed, or corroded. Direct fit.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Interior support trim that secures the door assembly and provides a finished surface inside your washer door. Replace when cracked, damaged, or worn.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Appliance won't power on? This power cord assembly restores electrical connection when the cord is damaged or has poor contact. Direct plug-in repair.

Cabinet base assembly for washers. Replaces cracked, rusted, or corroded base frames. Installs at bottom of washer cabinet to support unit weight.

Secures internal washer components and maintains proper alignment. Replace when brackets are worn, broken, or causing rattling. Confirm fit with your model number.

Leveling leg assembly for washers and laundry centers. Installs at the base to support and level the unit. Replace if cracked, broken, or missing.

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle

Replacement handle for laundry center doors. Installs on front panel for opening and closing access. Needed when original is cracked, broken, or missing.

This drain hose cap seals the end of a dishwasher or washer drain hose to prevent leaks and help keep odors and debris from entering the drain line. It restores a snug, secure hose termination for reliable draining. What it does

• Seals the open end of a drain hose to reduce water leaks at the hose termination.
• Helps prevent sewer odors or debris from traveling back through the hose.
• Keeps hose connection clean and reduces risk of clogging at the open end.
• Useful when replacing a damaged or missing hose end cap to maintain proper drainage.

• Disconnect power and turn off water supply before servicing the appliance.
• Remove the old cap and inspect the hose end for damage or buildup; clean as needed.
• Push the cap onto the hose end until fully seated; verify a snug fit and no visible gaps.
• Test by running a short drain cycle and checking for leaks; replace if cap doesn't seal.

Fix washer control issues or electrical failures with this wire harness assembly. Connects control components for proper operation. Moderate DIY repair.