Lg Washer WM2455HS Parts

This washer tub assembly is the stationary outer drum that contains wash water and supports the spin basket and drive components. Replace a cracked or worn tub to stop leaks and restore smooth, quieter spin performance.

• Forms the sealed outer container for wash water and houses the spin basket
• Provides mounting points for suspension, motor, and hoses (varies by model)
• Keeps the basket aligned for balanced, quiet operation
• Typical symptoms of failure: water leaks, roaring/grinding during spin, excessive vibration, or visible cracks

• Unplug the washer and shut off water; the tub is bulky—use two people and wear gloves
• Remove panels as needed for access, then disconnect hoses, wiring, suspension, and drive components to free the tub
• Transfer all reusable parts from the original tub to the new tub in the same orientation
• After reassembly, check for leaks and run a test cycle/spin to verify operation

Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This metal hook mechanism secures the washing machine door in the closed position during wash cycles for safe operation. It engages with the door strike to create a tight seal and prevent the door from opening while water is present. Replace if the door won't latch securely, pops open during cycles, or won't unlock after washing.

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Outer door frame for front-load washers. Plastic housing that surrounds the door glass. Replace if cracked, broken, or damaged from impact.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This is a replacement screw used to secure internal components and assemblies. It restores proper fastening when original screws are stripped, loose, or missing. What it does

• Secures panels, brackets, or small assemblies to prevent rattling and misalignment
• Restores proper fit when original fasteners are worn, stripped, or lost
• Helps stop vibration-related noise from loose parts
• Matches OEM fastening locations and thread style for intended application

• Screw as shown

• Unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and dispose of damaged fasteners

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.

Replace your washer's drain hose if cracked, leaking, or damaged. Connects the pump to the standpipe for proper water drainage during wash cycles.

Washer won't spin or turns inconsistently? The stator assembly creates the magnetic field that drives the drum. Moderate DIY repair, 30-60 minutes.

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.