Lg Washer WM2477HS Parts

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Interior support trim that secures the door assembly and provides a finished surface inside your washer door. Replace when cracked, damaged, or worn.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Cabinet base assembly for washers. Replaces cracked, rusted, or corroded base frames. Installs at bottom of washer cabinet to support unit weight.

Fix washer leaks or slow draining with this drain pump hose. Routes water from the tub to the pump during drain cycles. Easy DIY repair part.

Replace your washer's damaged or broken frame panel. This structural cabinet panel restores the outer housing when cracked, dented, or missing.

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle

Replacement handle for laundry center doors. Installs on front panel for opening and closing access. Needed when original is cracked, broken, or missing.

This drain hose cap seals the end of a dishwasher or washer drain hose to prevent leaks and help keep odors and debris from entering the drain line. It restores a snug, secure hose termination for reliable draining. What it does

• Seals the open end of a drain hose to reduce water leaks at the hose termination.
• Helps prevent sewer odors or debris from traveling back through the hose.
• Keeps hose connection clean and reduces risk of clogging at the open end.
• Useful when replacing a damaged or missing hose end cap to maintain proper drainage.

• Disconnect power and turn off water supply before servicing the appliance.
• Remove the old cap and inspect the hose end for damage or buildup; clean as needed.
• Push the cap onto the hose end until fully seated; verify a snug fit and no visible gaps.
• Test by running a short drain cycle and checking for leaks; replace if cap doesn't seal.

Replace your washer inlet hose if you notice leaks, cracks, or reduced water flow. Connects water supply to your washing machine. Verify fit with your model.

This rear cover is the exterior cabinet panel that protects the appliance's internal components and helps maintain proper airflow. It restores a finished back surface and prevents debris or pets from contacting working parts. What it does:

• Protects internal parts from dust, spills and physical damage
• Helps direct airflow and maintain proper ventilation paths
• Replaces cracked, warped or missing back panel that can cause rattles or expose components
• Reduces risk of foreign objects entering the appliance and interfering with operation

• One rear cover panel

• Disconnect power and any fuel lines before beginning repair
• Remove existing access panels and fasteners; retain hardware if reusing
• Handle edges carefully—metal panels can be sharp

This OEM replacement part is a washer door assembly. The washer door assembly consists of the main components that make up the front door of the washer. Over time, a washer door can become inoperable due to excessive wear and tear. If the washer door is no longer shutting or opening properly or is damaged to the point of inoperability, it will need to be replaced.To replace the washer door, start by making sure the washer is unplugged. Once it has been powered off, proceed to open the door. Locate the screws that attach the hinges to the door. Unthread the screws and lift the door off from its hinges. Set the old door to the side and proceed to place the new door on its hinges. Fasten the screws that secure it. Once secured, open and close the new door to make sure it is functioning properly.This authentic OEM part is sourced directly from the manufacturer and is compatible with LG brand washers.

Color: blue. Measures about 2-1/2 inches wide by 4-1/2 inches deep.