Samsung Washer WR-HC137UH Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

I watched the you tube video that completely explained how to do it. It was very easy to do. Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

First indication something was wrong when the washing drum starting to violently bang against the inside of the washer while in spin cycle. Then, when I opened the washer door, a misty smoke came from the inside. With the video from Appliance Parts Pros, disassembly of the washer was no problem. First, I replaced the four shocks on the washer drum. But, after a test run, determined that it was spider arm assembly. Again, the series of instructions made getting to the part fairly easy. The... Read more

Followed the excellent videos provided by AppliancePartsPros. Made a multi step repair, if not simple, then extremely less complicated. Loved the way they showed the step by step disassembly as well as the step by step reassembly. Great videos. Got the right parts the first time and very fast delivery. Can’t say enough good things about AppliancePartsPros.com Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

• Will not stop filling with water

Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

At first I thought it was the bearing, but when I got it apart I found the main shaft had corroded from possibly the soap powder and bleach combo build up on the part. After I cleaned it all up I found one of the three mounting braces was cracked and causing the unit to shake during the spin cycle. Once I replaced that part and replaced a few missing parts I lost all found on your store the unit went together just as it came apart and works excellent. Read more

Went online to repairclinic.com and it was a simple as typing in the serial # to find the correct parts. Shipping was very quick and the handle was completely repaired within days. Read more

When we first removed the drain filter from the washer, we noticed the O-ring had a slight defect which made removal hard and reinstallation almost a nightmare. Finally we ordered another filter when we ordered a water valve/thermistor for the mother-in-law's washer. Filter installed a lot easier than the original one. Should have ordered one way sooner! Now on to the washer. Read more