Parts for Bosch WFMC6401UC/03: Pump Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement hose connects the dishwasher drain/sump to the drain system, restoring proper water removal and preventing leaks or standing water. It's a direct-fit service part when the original hose is cracked or clogged. What it does

• Carries waste water from the dishwasher sump to the household drain or disposal
• Restores proper draining when a split, collapsed, or clogged hose causes standing water
• Helps stop leaks and puddling that can occur from worn or damaged hose sections
• Maintains correct flow to prevent dishwasher error codes related to drainage

• Turn off power and water supply to the appliance before starting any repair
• Inspect hose routing and clamps; replace any damaged clamps or retainers for a secure seal
• Ensure hose connections are tight and routed without kinks to allow proper drainage

This installation set provides the hardware needed to mount and connect a compatible appliance, helping ensure a secure fit and correct hookups during installation. Designed as the ready-to-use kit installers expect. What it does:

• Provides the mounting and connection hardware used during appliance installation
• Helps prevent loose fittings and reduce leaks caused by improperly secured components
• Useful when original installation parts are missing or damaged
• Supports a proper, stable installation for safe operation

• Follow the appliance's installation instructions and local codes when installing this kit
• Turn off power and water supply before beginning work
• Use appropriate tools and verify all connections are tight and leak-free after installation

The Hot Water Inlet Hose is an OEM replacement part for Bosch washers. It serves as a flexible supply line that delivers hot water from an external water heating hot water heater directly to the washer. This hose plays a key role in optimizing wash performance through consistent delivery of hot water for optimal cleaning and sanitization. 

Causes of a bad hot water inlet hose can include wear and tear over time, repetitive flexing weakening the hose material, mineral buildup restricting flow, or damage due to sharp edges or crushing forces.

Symptoms of a bad hot water inlet hose include: 

• Loss or reduction of hot water during wash cycles
• Decreased cleaning ability from insufficient water heating 
• Visible kinks, cracks, or splits along the hose body
• Leaks or drips at hose connections under the washer

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Cold Water Inlet Hose is an OEM replacement part for Bosch washing machines. It serves as a flexible supply line that delivers cold water from an external plumbing source directly to the washer. This hose plays an important role in providing a balanced mix of hot and cold water flow into the unit.

Symptoms of a bad cold water inlet hose include:

• Fluctuations in water temperature during cycles  
• Issues with certain temperature settings like warm or cold not operating properly
• Visible cracking, kinking, or leaking along the hose body
• No water flow or pressure at the cold supply 

Causes of a failed cold water inlet hose can be mineral deposits clogging the line, natural wear and tear over time, or physical damage from crushing or abrasive surfaces compromising its integrity.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models.

The Cold Water Inlet Valve is an OEM part for Bosch washing machines. It is designed to regulate the flow of cold water into the washing machine during the wash cycle. This valve operates based on signals from the washing machine's control board, ensuring the right amount of cold water is provided.

Causes of a faulty cold water inlet valve can include wear and tear over time, clogs or blockages in the valve, electrical issues, or valve failure.

Symptoms of a bad cold water inlet valve may include:

• Insufficient or no cold water flow into the washing machine
• Leaking or dripping water from the valve during the wash cycle
• Inconsistent or inadequate water supply for washing clothes
• Error codes related to water supply or filling

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Note: For the Hot Water Valve, order part number 00422245.

The Hot Water Inlet Valve is an OEM part for Bosch washing machines. It regulates the entry of hot water into the machine, crucial for cycles requiring warm or hot washes. Activated by the machine's control system, this valve opens at the precise moment to allow the correct amount of hot water to mix with the cold, ensuring the selected temperature setting is accurately achieved. 

The causes behind issues with the hot water inlet valve often include sediment build-up from hard water, wear and tear from regular use, or electrical failures preventing the valve from operating.  

Symptoms of a malfunctioning Hot Water Inlet Valve include:

• Water that is too cold 
• No water entering the machine 
• Leaks around the valve area 

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This hose inlet is the molded connection that routes incoming water into the appliance and provides a sealed mating point for the fill hose. It restores proper water flow and helps prevent leaks at the hose connection. What it does

• Directs incoming water from the fill hose into the appliance's water system.
• Provides a sealed connection to prevent drips or leaks at the hose attachment.
• Can cause no-fill or slow-fill symptoms when cracked, clogged, or loose.
• Works with the inlet hose and nearby fittings to maintain correct water supply.

• Turn off power to the appliance and shut off the water supply before starting.
• Inspect and replace any damaged gaskets or clamps when installing this part.
• Hand-tighten fittings, then snug with appropriate tools; avoid overtightening plastic fittings.
• After installation, restore water and power, run a short cycle, and check all connections for leaks.

This flow-through sensor monitors the dishwasher's water flow to help ensure correct water delivery during cycles, supporting consistent wash performance. Replaces a worn or failed sensor to restore proper flow detection. What it does:

• Detects and reports water flow to the control so cycles run with correct water movement
• Can cause wash performance issues or flow-related error codes when faulty
• Helps the appliance regulate fill and wash timing based on measured flow
• Works as part of the dishwasher's water-management system with wiring harness and mounting

• One flow-through sensor

• Disconnect power to the appliance before beginning any service
• Handle the sensor and wiring carefully; observe connector alignment when reinstalling
• Replace only with the identical part number

This T-shaped water hose connector routes incoming water to separate internal hose lines, restoring proper water distribution inside the appliance. It replaces a worn or cracked hose tee to stop leaks and restore flow to internal components. What it does:

• Joins three water lines so water can be directed to multiple internal points
• Stops leaks caused by cracked or damaged tee fittings at hose junctions
• Restores reliable water flow to downstream parts that depend on the split connection
• Prevents hoses from separating at a failing junction

• Turn off and disconnect the appliance from the water supply before servicing
• Inspect hose ends and clamps; replace clamps or seals if worn
• Push hoses fully onto each barb and secure with appropriate clamps
• After installation, restore water and check all connections for leaks

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This fastening ring secures mating appliance components by locking parts in place to prevent movement or separation during operation. It's a simple yet essential hardware piece that helps maintain proper alignment and reliable function. What it does

• Holds mating parts together to prevent wobble, vibration, or dislocation
• Keeps seals and assemblies properly seated to reduce noise and misalignment
• Helps maintain correct component spacing for smooth operation
• Commonly replaced when the original ring is bent, worn, or missing

• Designed for use with compatible OEM assemblies; follow for correct placement
• Inspect mating surfaces and replace any damaged clips, seals, or gaskets before reassembly
• Use proper tools to avoid deforming the ring during installation; do not force into place
• Disconnect power and follow safety procedures before servicing the appliance

Hose-inlet directs incoming water from the household supply into the appliance's inlet assembly to allow normal filling and prevent leaks. Replace a cracked or damaged inlet hose to stop visible leaks and restore proper water fill. What it does:

• Routes water from the home supply to the appliance inlet assembly.
• Stops leaks caused by cracks, splits, hardened or collapsed hose material.
• Can cause slow fill, no fill, or visible leaks at the connection when damaged.
• Used as a replacement part where the original inlet hose is worn or leaking.

• Always shut off the water supply and disconnect power before starting work.
• Drain remaining water from lines and have towels handy to catch residual water.
• Inspect fittings and seals; replace clamps or O-rings if worn to ensure a watertight connection.
• After installation, restore water and power and check all connections for leaks.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This temperature sensor (thermistor) measures internal temperature and sends readings to the appliance control to help maintain proper operation and cycles. It replaces a failed sensor so the control can accurately monitor temperature. What it does:

• Senses temperature and provides a variable resistance signal to the control board
• Helps the appliance regulate cooling/heating cycles and defrost timing
• Commonly associated with incorrect temperature, improper cycling, or temperature-related error codes
• Used wherever precise temperature feedback is required by the control system

• One temperature sensor (thermistor) with attached lead/harness as shown

• Disconnect power to the appliance before accessing or replacing the sensor
• Handle sensor and wiring gently; avoid pulling on the lead or bending the sensing element
• Reconnect connectors fully and route the harness away from moving parts or high-heat areas

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.