Mike K June 13, 2013 for Model Number shv4303uc/u11 After the on button is pushed on and the cycle button is depressed, the indicator light comes on and you shut the door the cycle starts then stops.Open the door and indicator light is off. Tried to run a diagnostic cycle...turned unit on depressed the 2 cycle buttons. lights came on then slowly dim and go out. If I try this again..nothing happens. If I flip the breaker off for a while and do this again it works. Each time is shorter, now it doesn't work at all. Checked the on/off switch...2 pairs of controlled wires...both pair show continuity when switch is on. I'm leaning toward the control module as the problem. Does this sound reasonable? Thank you
Bill I June 01, 2013 for Model Number She65po5uc/63 The Bosch dishwashers pump will not shut off. If the power is on the pump runs even if the door is open. The dishwasher will not run through any wash cycles and the push buttons on the open have no effect.
1 Answer Bill, This issue would most likely be caused by a bad water valve on the unit. The flood switch is being activated which would be caused by a faulty water valve. Read More...
Sam May 17, 2013 for Model Number SHE44C06UC/48 If you push the "on" switch the motor starts before you close the door. Close the door but no water comes out. The motor starts with the door open. No water comes out. Close the door and the motor still runs forever but no water. Is this a control unit problem? Read more: http://www.appliancepartspros.com/bosch-control-module-with-481055-ap2804411.html#ixzz2Tbtxg9sP http://www.appliancepartspros.com
1 Answer Hello Sam. Yes, based on the information you provided, it sounds like the control module is bad and will need to be replaced on the unit. Read More...
Jay April 12, 2013 for Model Number Bosch SHU9915UC/11 If you push the "on" switch the motor starts before you close the door. Close the door but no water comes out. The lights on the control panel only come on when the off/on switch is put "on". The motor starts with the door open. No water comes out. Close the door and the motor still runs but no water. Is this a control module problem? Thank you, Jay H.
1 Answer Hello Jay, It sounds like the drain pump is probably the motor you are hearing. This explains the no fill and the motor on with the door opened. You will need to replace the water inlet valve 00425458 and while you have the old one off, before installing the new one, use the opening where the new one goes to access the base. Use a teri-cloth towel not washed in fabric softener to "wick" the water out of the base. This will stop the drain pump from cycling on with the power switch turned on. Once you have ALL of the water removed from the base assembly, install the water inlet valve, check for leaks, and you should be ready to do dishes. Read More...
Roy March 07, 2013 for Model Number Bosch shu9915uc/uc11 Our dishwasher will not end the cycle. We started it as usual. Later we heard the pump still running, and opened the door. The soap door had not opened, the water was gone and the pump kept running. Now if you turn on the on button the pump just runs. Also the cancel drain function does not work. Is it the control module?
1 Answer Hello Roy, You should check in the bottom of the base of the dishwasher through the water valve opening for water standing in the base. If the water valve is the issue, it will not be an electrical issue but a mechanical one. The valve will still open, but not far enough to allow a full flow of water. The water in the base assembly of the dishwasher is the key we are looking at. You might even be able to tell with a flashlight and an inspection mirror. The water will puddle in the bottom of the dishwasher base if the water valve is the issue. Replacing the water valve 00425458 should correct the issue. The water in the base will have to be wicked out with a towel to stop the flood switch from tripping the drain pump on. Read More...
1 Answer Hello Bill. If the water will not stop, and you have to turn off the shut off, you will need to order and replace the valve 00425458 on the unit. Read More...
Ec November 11, 2011 for Model Number shu9925uc/u12 My dishwasher does not turn on, the light at the on-off button does not light-up, is this indication that the control module is out, there is power at the outlet.
1 Answer Hello EC. You will need to test and see if there is power at the on/off switch 00165886. If so, check and see if it is sending power to the control module 00481055. If not, replace the switch. If so, replace the module. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...