Greg December 13, 2022 for Model Number Siemens ultraSense plus Washer Model#WFX8400UC The washer starts as usual dispensing water/detergent and stops at the normal level. Then it displays "auto load adjustment" and does nothing for 2 minutes. The display then changes to "Washing" and the machine goes through the complete wash, rinse, and drain cycle but the motor does not spin at any time. Have voltage to the motor so thought it was defective and replaced it with a brand new Bosch so it's not the motor. Also checked the pressure switch tubing which is clean from the air gap to the switches.
1 Answer Hello Greg, You should first check that voltage is being supplied to the motor control unit 00436461. If so, you should then check to see that power is being sent to the motor assembly. If so, replace the motor assembly. If not, the motor control unit is the part at fault. I'm sorry but this part 00436461 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
Charlie February 18, 2020 for Model Number WFMC3200UC/01 My washer will not spin, I checked the belt and it is working good. Any ideas what could be wrong?
1 Answer Charlie, Several things have to occur for the washer to spin. The door has to lock and remain locked during the cycle, the washer has to drain all the water out and the water level switch has to reset to the "empty" position. Those are the "easy" checks(just run the washer and observe what happens), Then you'll need to check the wiring harness between the motor control board in the base of the washer and the main control board in the control panel. If all checks are OK, then replace the motor control board assembly. Read More...
Ugo December 13, 2019 for Model Number WFMC3200UC-01 Hi, Our washer doesn't control water inlet correctly. Most of the time, it will start letting water come in the drum at the beginning of the cycle, but it won't stop the water from flowing in. What we do in this case, is that we close the water valve on the wall behind for a few seconds, then we re-open it and the washer is ok. It happens on the wash and rinse part of the cycle. An appliance repairman went here and he tested the valve. He said that the valve is doing its job, that we should replace the main board, but it's almost the price of a new washer. I found one for 100$ on Ebay, replaced it but the problem is still there. What should I do? Replace the water sensor, the valve, or something else? The problem is not always 100% constant but it happens almost every time we wash. Thanks,
1 Answer Ugo,this sounds like a typical water valve problem. To test , once this occurs unplug the washer from power, if the water continues to flow replace the water valves, 00422244 and 00422245, if the water stops then its a control board problem. Read More...
J.J. January 11, 2018 for Model Number wfmc3301uc/09 My washer will not start when the start button is pressed. I had a technician take a look and he managed to get it to operate when the start button is pressed but says the control module must be replaced. He said he must order the part and install it once it arrives. This will be an additional 60 dollars when he returns to complete the repair. I already paid 90 dollars for him to come and diagnose. Do you think it could just be the start button?
1 Answer Hello J.J., I'm sorry but the "start button" is part of the control board 00660809 so the technician is most likely correct in his diagnosis. Read More...
Joe Tanglewood November 12, 2017 for Model Number wfm8410sw01 I get an F20 code at different parts of the cycle. Sometimes in the wash cycle and sometimes I believe when it goes to rinse cycle. I have found if I run it in 'clean' setting I get a consistent failure. It will fill up, turn clockwise, stop, ccw, stop, start a faster turn (wash?) and the go to F20. I have replaced the drain pump (broken impeller), cleaned filter, replaced the pressure switch., cleaned all wiring connections with contact cleaner. Could the new pressure switch be bad or am I looking a a computer or something else?
1 Answer Joe, The F20 0r 20 error code on Bosch washers indicate a problem in the spin cycle. You'll need to check the wiring harness between the main control board and the motor control board. replace the motor control board if all's OK. Read More...
Charles July 19, 2017 for Model Number Bosch wfmc3301uc/03 Machine will not go into wash cycle- if I try to just spin, pump drains and drum does not spin. Is it the motor controller board and if so what part number should I order. Thanks
1 Answer Hello Charles. You will need to check the motor 00660487 and the motor board 00660486 on the unit. Either one can cause this issue. You will need to use diagnostics and see which part has failed. Thank you. Read More...
1 Answer Hello Leon. Test for power to the motor. If there is power there and the motor does not run, you will need to order and replace the motor on the unit. If there is no power there, the motor control unit may need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
James July 18, 2013 for Model Number WFMB3200UC/01 My bosch washer will wash the clothes but will not spin them out at the end...What could the problem be?
1 Answer Hello James. Make sure the door lock assembly is good, and the pump filter is clear without any clogs in it. Read More...
Dan May 15, 2013 for Model Number WFMC3200UC/01 Good morning, I received the part, AP3782696, a few days ago, but unfortunately, it doesn't fit correctly. It has the correct number of wires and the connector is the same, except that the guide pins on the connector do not align with the grooves in the motor control unit AP3672788 (436461). The cable harness is supposed to connect the motor control unit of a Bosch WFMC3200UC/01 washer with the motor. Do you have a parts diagram and list that can confirm that this is the correct part, or can you tell me which is the correct cable harness? Thank you for your help. Dan
1 Answer Dan, Based on your model number this cable harness 00421571 is the correct part number for your unit. Read More...
Larry March 04, 2013 for Model Number WFMC3200UC/01 The washer will not spin. The door is locked. The pump runs and takes the water out. The minute indicator has 8 minutes on display. The tub turns back and forth, and the the indicator goes to 2 minutes and the washer shuts off. What could be causing this?
1 Answer Larry, You will want to double check the pump to ensure that there is no clogging of pump or of the drain lines. Check to make sure that the pressure hose is not kinked or clogged which would cause the unit to think it still has water in it. If these check ok then you would want to check the connections of the motor control to ensure good connections and check the door latch to make sure that all switches are closing properly. Read More...