Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Dishwasher Check Valve by Bosch

Best Seller
Manufacturer Part
4.89 (64)
By: Bosch
Part Number: OEM8407161
Manufacturer Part Number: 00165262

Fix dishwasher not draining or foul odors with a new check valve. Prevents dirty water backflow into clean dishes. DIY-friendly repair in 1-2 hours.

More
$11.54

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Bosch Dishwasher Check Valve (Part Number: OEM8407161)

Bruce for Model Number SHU4016UC/06

This 22yo Bosch SHU4016UC/U06 dishwasher kept getting stuck in wash cycle. I checked and cleaned filters at bottom of washer. That seemed to help, then got stuck again. So I removed the black rubber check valve and found that it was torn in 2 pieces - the coin shaped disc was torn from the rest of it. I ordered replacement Check Valve 00165262 / AP2802384 and got it in the mail. It seems different from the one I removed: 1. The color/material is different. Old one is black rubber. New one is clear/translucent. 2. Old one is stamped number "3". The new one is stamped "11". 3. Size of the old disc shaped part of the valve is noticeable bigger than the new one. I double checked part numbers online and everything indicates this is the correct replacement check valve, but it looks different. Is this the correct replacement check valve for my dishwasher?

1 Answer

Bruce, the check valve 00165262 would be used with the model number provided. The design has slightly changed to allow it from sticking in the closed position.

Read More...

1 Answer

That is possible but I would double-check the entire installation to be sure the hoses are installed properly as well.

Read More...

1 Answer

David, if the water is at the bottom of the sump where the aqua sensor is, this is normal as the drain pump is not going to be able to pump all of the water out. The drain pump utilizes water to push water through the drain, which causes a little bit to be left in the sump assembly.

Read More...

1 Answer

Shilpa, the drain of the model provided does utilize a check valve 00611320 at the sump where the drain hose would connect into the dishwasher.

Read More...

1 Answer

Negel,
Check and see if the main control is sending voltage to the drain pump. If your getting 120 vac to the drain pump them your pump is faulty or you have a clog may be in the drain line. And if valve continuously fills just curious how you are stopping that. Do you have to turn off the water supply? Possible stuck relay on the control or the solenoid on the valve is stuck open. With both issues, I'm leaning more to control but I would test these things.

Read More...

1 Answer

Hello Roger,
If the drain pump is getting 120Vac when it should be draining but the pump is not running, make sure nothing is in the impeller. If nothing is in there preventing the pump from running and the filters are clean and there are no clogs, you will need to replace the drain pump 00642239. (This is also if the garbage disposer has not been replaced and the knockout in it has not been knocked out.) If you are not getting 120Vac to the drain pump, you may need to replace the control board 00647474. IMPORTANT NOTE: The manufacturer has a note by this part stating that the customer should contact them at 1-800-944-2904 to make sure this is the correct part number for the model number on the units' I.D. tag.

Read More...

1 Answer

Will,

The non return valve on this unit would be part number 00165262. You may also want to try to run a clean cycle on the unit which you could use glisten dishwasher cleaner W10549845 to do this.

Read More...

1 Answer

Bob,

The non return valve 00165262 would be located on the out port of the sump assembly where the drain hose would connect to the sump. If the non return valve is not there then it would need to be replaced. You will also want to check the impeller on the drain to make sure that the impeller is not damaged.

Read More...

1 Answer

Hello Karen. If there is water in the base, you need to repair the leak in the unit. If there is no water in the base, you need to check and see if the float is stuck in the unit.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google