Dyilady73 February 26, 2014 for Model Number SHU9955UC/U12 The black pastic on/off button seems to have broken as it does not connect with the on/off switch behind it. Can the black plastic piece be replaced and are there instructions how?
1 Answer Hello DYIlady73. Yes the button Part# 00184588 can be replaced easily. Here are the instructions from the manufacture for the module. This will get you access to replace the On & Off switch 00175338. Hope this helps. 1.Remove fascia panel by removing six (6)T-20 Torx inner door screws.2.Disconnect wire harnesses from module after noting connector locations. 3.Remove fascia panel from console by removing four (4) T-20 Torx screws.4.Remove two (2) T-20 Torx screws holding module to console.5.Carefully pry back locking tabs on each front corner of module, then remove module from console. Remove button pad from module. Read more: http://www.appliancepartspros.com/bosch-switch-on-off-175338-ap2821521.html#ixzz2uRcH5Kt4'>http://www.appliancepartspros.com/bosch-switch-on-off-175338-ap2821521.html#ixzz2uRcH5Kt4 http://www.appliancepartspros.com Read More...
John O. March 11, 2013 for Model Number shu9955uc/14 My on/off switch works but black plastic casing with on/off seems to have broken. Do you sell that piece seperate from switch?
1 Answer John, the on/off button is part number 00184590 and the control panel is part number 00184595. You'll need to inspect both parts and replace the defective item. Thanks! Read More...
Gary February 04, 2013 for Model Number SHY66C02UC/14 On OFF switch works, but plastic surrounding to keep it in place has broken away and it flops about. What part?
1 Answer Hello Gary. Based on the model number, you will order and replace part number 00175338. Read More...
Becker November 13, 2012 for Model Number SHU9955UC /UC12 The machine (Bosch SHU9955UC) is dead I suspect it was due to voltage spike during the last storm. Not sure there is a fuse or any kind of protection against overvoltage, but I tested the main on/off switch (i believe is similar do the 175338, but Bosch's p/n is 280501 or Dreefs 4783/12) for continuity and the switch seems to be working in 5 of the 6 blades. The now open wire feeds into the control board. I hope you can help me answer the following questions: - is this switch also responsible for protection of the machine & control board ? - since 5 blades in the connector are working do you see any problem in inserting a jumper in connector ? - Where can I find a datasheet for the switch ? - Where can I find a circuit diagram of this machine ? Thank you in advance for your help. Becker
1 Answer Hello Becker. If you turn on the switch, and it does not close to send power to the control board, you will need to replace the switch 00175338 on the unit. Read More...
Rick February 05, 2012 for Model Number shu9955uc/uc12 Dishwasher just wont turn on. It is pluged in an I checked my fuse box. Will replacing this solve my problom?
1 Answer Hello Rick. Test the on&off switch 00175338 for continuity. If it checks bad, you will need to replace it. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Gregg K. July 10, 2011 for Model Number SHU9955UC/UC12 I have the part. I need instructions on how to install the on/off switch. Where can I get the instructions?
1 Answer Hello Gregg. Here are the instructions from the manufacture for the module. This will get you access to replace the On & Off switch 00175338. Hope this helps.1.Remove fascia panel by removing six (6)T-20 Torx inner door screws.2.Disconnect wire harnesses from module after noting connector locations. 3.Remove fascia panel from console by removing four (4) T-20 Torx screws.4.Remove two (2) T-20 Torx screws holding module to console.5.Carefully pry back locking tabs on each front corner of module, then remove module from console. Remove button pad from module. Read More...