Jenny June 10, 2021 for Model Number NX58J5600SG/AA My 3 year old Samsung gas (converted to propane) range stopped working. The propane tank is full, all burners click when you turn one on, one burner lights but only stays on for a few seconds and the others won't light at all. All the components are clean, the stove is not used heavily. Also, the oven temperature has never been accurate. Too cold at lower temperatures and too hot at higher temperatures. Usually 25-50 degrees either way. For the first issue, do I need to replace the valve & pressure regulator?
1 Answer Jenny, For the issue of the temperatures it would be best to check to make sure that the oven sensor resistance is 1090 ohms at room temperature. If the sensor is good then it would be an issue with the control board. As for the top not working, this would most likely be an issue with the gas regulator that would need to be replaced. Read More...
Kristi December 28, 2020 for Model Number WFMC2201UC/15 I want to replace both hot and cold inlet valves in my Bosch washer. Is the valve magnet (00422245) the hot water inlet valve? Or do I need something else?
1 Answer Kristi, The cold water valve will be part number 00422244 and the hot water valve is part number 00422245 Read More...
Richard June 23, 2020 for Model Number WFMC5301UC/13 softener not dispensing. I removed assembly and thoroughly cleaned it by opening the appliance and disconnecting the hoses, etc, and returned it and re assembled to washer, but Still not dispensing the softener! What else could I do? Please help! PS. The bleach compartment runs water through it on rinse cycle and I will find water in softener area at the end of a complete cycle but softener still there...? Thank You!
1 Answer Hello Richard, this type of dispenser is dependent on the water valves operating correctly, the repair would involve replacing the water valves 00422244 and 00422245. Read More...
Chris June 04, 2020 for Model Number WFXD5201UC Washer stops mid cycle and door unlocks, stuck electrical display until it is turned off and then back on... replaced the door lock with a part from y'all. Still doing the same thing... what else could it be other than the Door Lock? thanks
1 Answer Chris, it is possible that there may be a control failure. However, the model number provided is not registering as a valid model. If the model and serial numbers could be verified and provided in a new inquiry, this will allow for the most accurate information to be presented. Thank you for your patience and understanding. Read More...
Darren Williams January 04, 2020 for Model Number WFK2401 When I start wash cycle there is no hot water. Have to run cycle in cold water. Checked both screens, clear.
1 Answer Darren, Check to see if there is power getting to the hot water solenoid on the unit and if there is power but no hot water coming through then the issue will be a faulty valve. If there is no power then the issue will be a faulty control board. Read More...
Lan November 09, 2019 for Model Number Bosch washing machine WFMC640SUC/02 My washer did not agitate in the rinsing phase and did not run the final spin. What is its problem? thank you
1 Answer Lan, the issue could be caused by several things. To identify what may be causing the issue, an error code can be found by rotating the selector knob to the off position then pressing and holding the menu and the select buttons at the same time. While holding these buttons, rotate the selector knob counterclockwise until it is on the permanent press cold selection. When the knob reaches this position, P1: ERRORS should show. With this showing, press the flashing start button to enter the fault codes listings. This will allow for the menu and select buttons to no longer be pressed so that the errors can be cycled from the most recent to the least recent error by pressing the menu button. Read More...
Ron August 17, 2018 for Model Number WFMC5301UC/12 Water keeps running into the machine even after cycle is over. Do I just need the magnet part of the valve, or more than that?