Mark September 18, 2022 for Model Number FAFW3517KR1 When starting the washer it gives error code 90 i have to unplug the washer and plug back in to get the washer to kick on what item/items do i need to replace
1 Answer Mark, Error code 90 is a group of error codes dealing with a communications error between the control panel and the main board. This could be an issue with the wiring or connections or one of the boards. You should check the wiring and connections and if this does not solve the issue you will need to replace one of the boards and if it still doesn't solve it replace the other. Read More...
Dale November 06, 2021 for Model Number electrolux atf8000fs1 panel light up and when you push start it goes off. one time gave error code 1
1 Answer Dale, Thanks for the question!!! There is no error code of 1 listed for your model. The best approach at this point would be to open the washer and look inside for your tech sheet. It has a diagnostics mode that will help identify the issue with your washer. Read More...
Jeff July 19, 2021 for Model Number ATF7000EG0 Washer will not drain. Pump kicks in for a second then shuts down even in diagnostic mode. Shows E45 code. Took the pump boot off and no obstructions? Control board issue?
1 Answer Jeff, the error E45 indicates a failure in the main control 137007000NH and that it would need to be replaced. Read More...
Christopher Early July 25, 2020 for Model Number ATF8000FE1 Hello. Came home from work one day and needed to wash laundry, loaded the washer started the cycle. Water turned on for about 3 seconds and shut off then came on again for another 3 seconds and shut off, (also does this on spin only with the drain pump). The tub will not rotate. Tested the motor appears to be fine, changed the motor board and still nothing. So the question I have is, What could cause this? I don't want to keep buying parts and have the part I buy not be the problem. Thanks for your time Christopher Early
1 Answer Christopher, It would be recommended to get the tech sheet out of the unit and put it into a service diagnostic mode to see if there are any error codes. If there are it will point you in the direction of what may be wrong. Read More...
Robert September 25, 2018 for Model Number DAFW3577KW1 the machine does not turn on at all. there is power in the outlet.
1 Answer Robert, We will need to know a little more. Will display light, can you select a cycle, any noises when trying to start. If you wouldn't mind can you post another question with this info. Read More...
Mike February 15, 2016 for Model Number FAFW3577KR1 My machine runs in all settings for only 5-6 sec. I have replaced the door latch assembly and the main control board but I'm still getting a code E5E..
1 Answer Hello Mike, This is a communication error. Check the wiring between the control board and the speed control board. If the wiring is bad, correct the wiring problem. If the wiring is good, replace the control board 137007010. If the problem is not corrected, replace the speed control board 5304504863. Read More...
Scott May 25, 2015 for Model Number ATF8000FG1 I have been dealing with E56. I have done test 9: motor spins well; tub spins free. Drive motor tests at 4ohms. Says replace speed control board - been trying to figure out what the "speed control board" might be - part 60? HELP!
David April 29, 2015 for Model Number ATF7000EP0 I have error code 31. I have replaced both control boards with new ones from you. Where is the pressure sensor! I see the pressure switch but am lost as to where the sensor may be! Part# or location or any help would be appreciated! All diagnostics work when cycled except 31!
1 Answer Hello David. Slide the top off the washer to access and replace the pressure switch 134762000. Read More...
James L. February 06, 2015 for Model Number ATF7000EE0 Washer will not spin. Drum goes back and forth during wash cycles but will not final spin. Was able to get a code e47. Replaced spin control board part number AP3891780. Did not fix problem. Can here water being pumped out during final spin but tub doesn't move.
1 Answer James, You will want to check the door latch on the unit. If the door latch is not working properly it will cause the unit to not spin. You will want to check the following Remove the door lock assembly and measure the resistance of the PTC. Shorted or open. Defective door lock assembly. Reads around 1500 Ohms. Defective control board Read More...
Sam January 26, 2015 for Model Number ATF7000FSO My daughter asked for help with her 7000 series washer. I used the trouble shooting tips and got error code E68. Ordered the heater part and went to the next town to install heater. We measured the resistance for 4 ohms prior to removal and compared both old and new and measured 14 ohms. Did not remove the old heater. Looked like the heater was ok so I followed the wires colors up to top right front and found the small control board 134558200 had come loose from the control panel face and knocked the spade terminals loose from the p c board. I repaired the p c board. Thank God for Radio Shack .I was able to get the unit working with some solder board trace repair , solder and a soldering iron. I will need to replace the board but noticed although it looks similar from my picture to yours, my part says electrolux. Any issues with the swap. And of course I will need to return the unused heater. Web page may need an update since it stated resistance should be 4 ohms. Thank You,