Steve November 29, 2013 for Model Number ltf6700fs0 Washer will not start, you can unplug, plug back in, and everything is lit up, but the display just flashes between the time and pause. Pushing start does nothing, no door click, etc., just stays flashing between pause and time. I tested door switch at 1.24K ohms. Is this a main board problem? Thanks, Steve
Randy A. October 01, 2013 for Model Number ATF-6000FS1 Elecrolux Front Load Washer Washer cuts off and on, display panel blinks off and on. Sounds like control board?
1 Answer Hello Randy, This could be a control but it could also be a poor electrical connection. Each connector should be unplugged and reconnected one at a time and try to run the unit. If it corrects the issue, this was probably the case. If not, you should make sure the wall outlet is not loose. If you still have no luck, try the control 137006030. Read More...
Dogohio September 30, 2013 for Model Number LTF6000FSO Washer stops part way through wash cycle. Tested door lock and got a reading of 1556 ohms. Tested J2 pin voltage and got 69 volts black wire to ground and 122 volts red/black wire to ground, Replace the board?
1 Answer Dogohio, First check and make sure there's cold water at the faucet and the fill valve, and make sure there is cold water flowing during the fill cycle. If there's no cold fill, the washer will stop at the rinse cycle. The voltages and resistances at the door latch assembly are in range. if there's cold water in the fill, then check or replace the board. Read More...
Jimc August 20, 2013 for Model Number ATF6700FS1 When trying to start a wash cycle, when you turn the selector knob to select between Normal, Quick, Heavy Duty, etc., the indicator light jumps all over the place between the different cycles. It's like playing roulette and hoping that eventually it will land on the cycle you actually want. When it finally does, it runs OK. Do I need to replace the main control board? Thanks, Jim
1 Answer Jim, check the pin 134347700 and knob 134551210 first. Chances are they're OK, but check, then replace the control 137006030. Read More...
Steven August 10, 2013 for Model Number frigidaire affinity atf6000fs1 When running a load it skips the drain and spin cycle at the end. I get a e6e error code. usually I have to run a spin only cycle after I run a load so the clothes are not wet.
2 Answers Steven, " It sounds like the communication problem. Per the manufacturer recommendations (very inaccurate) you have to check the wires between the main control board 137006030 and speed control boards 134743500. If there is nothing wrong, the main control board should be replaced first." The E6E code is an unlisted undiagnosed error and believed to be a communication error, per the manufacturer. Read More...
Steven August 10, 2013 for Model Number frigidaire affinity atf6000fs1 When running a load it skips the drain and spin cycle at the end. I get a e6e error code. usually I have to run a spin only cycle after I run a load so the clothes are not wet.
2 Answers Steven, " It sounds like the communication problem. Per the manufacturer recommendations (very inaccurate) you have to check the wires between the main control board 137006030 and speed control boards 134743500. If there is nothing wrong, the main control board should be replaced first." The E6E code is an unlisted undiagnosed error and believed to be a communication error, per the manufacturer. Read More...
Brian July 08, 2013 for Model Number atf6700fs2 The washer starts fine, then part way through the wash it just stops. The timer then goes back to the original amount and the door lock indicator flashes slowly. When start and cancel are pressed together E48 comes up. When only the spin cycle is selected it will drain and agitate for a minute or two then the same thing happens. Thank you in advance for any insight!
1 Answer Hello Brian. Board thinks the door PTC circuit is closed. You need to replace the lock assembly on the unit. Read More...
Kathy May 20, 2013 for Model Number part #ps2338949 Error 91 I replaced the board and unplugged one wire at a time it plugged it to new noard but it saying it has an error.
1 Answer Kathy, The E91 error code is an indication that the User interface to main control board communication error. You will want to check the wiring between the main control and the user interface. If the wiring is bad then repair wiring and if good then replace the user interface. If problem still not corrected then replace the main control board. Read More...
1 Answer Hello Jua. The code 43 is Console control board thinks the door locking device has failed. You need to check the door lock assembly. Read More...
Jim S. April 16, 2013 for Model Number atf6700fs2 The lights on front keep flashing, but works if you cancel and then start. After done light start to flash again. I think from the picture it all comes out the front so wouldn't have to take dryer off. I think the control part is the problem any thing I should replace Jim
1 Answer Hello Jim. Based on the information you provided, it sounds like the control 137006030 is bad and will need to be replaced on the unit. Read More...