Lee Meyers September 22, 2018 for Model Number GLD2445RFQ2 My dishwasher will run for the first 35 min or so and then just stop. HD is in the window, not flashing, and just stay that way until I power it down. We did have a brief power outage the day before this started happening. I did try different cycles but the same thing happens. I think I need a new electrical control but I want to be sure. Thank you.
1 Answer Lee, The HD on the display will be for a water heating delay. This indicates that the water is trying to get up to temperature. Always make sure that you are running the hot water at the sink before starting the cycle. Check for a faulty thermostat, a heater that is faulty or it could be a bad control board. The HD should only last approximately 3 to 4 minutes. Read More...
Jack June 05, 2018 for Model Number Frigidaire Dishwasher FDB2415LF My dishwasher won't turn on. I reset the breaker and got it to work for part of a cycle, but then nothing. I have 3 of the small green lights flashing below the timer, but nothing else. Also, the electronics in the handle will click irregularly. Sometimes loud enough you can hear throughout the room. Is this the control board, or do I need to replace other parts too? Thanks
1 Answer Hello Jack, The lights remaining on usually indicate stuck keys on the touchpad. For the correct part number, we would need to ask you to please post a new question including the complete model number from your units' I.D. tag. Thank you for your patience and understanding in this matter. Read More...
Aaron November 21, 2017 for Model Number GLD2445RFC2 The dishwasher starts on the selected cycle, it fills with water, and then ask the unit actually begins to "wash" it shut down with PF displayed, along with the "hi temp" and "no heat dry" lights flashing. When starting the cycle the water is warm/hot and the unit will empty if cancel is selected prior to shutting itself down. There is nothing jamming or restricting the pump and the door lock works fine... The main control board was replaced 7 years ago...could it be the same problem? What else could it possibly be?
1 Answer Aaron, The PF error code stands for power failure and it appears in window when dishwasher is first installed, or when power has been interrupted. HI-TEMP WASH and NO HEAT DRY indicator lights will also flash. First, remove power to the dishwasher, wait a minute or so and restore power and start the dishwasher. If the problem returns, remove power remove the lower kick plate and check the wiring and connections inside the junction box on the lower front frame of the dishwasher. Make sure the wires are twisted together and the wire nuts are tightly twisted on the wires. If the problem persists, check the wire connections at the control board and replace the control board if the wires are OK. Read More...
Kenneth June 27, 2016 for Model Number FDB2415LFS0 Washer has power but will not start. push start and the "CL"shows in the display and nothing happens. Is this the lock switch or the control board?
1 Answer Hello Kenneth. You will need to check the strike, latch, and switches first. If working properly, then replace the board on the unit. Read More...
1 Answer Hello Charles. We need the model and serial number to determine a year. Thank you. Read More...
John November 11, 2015 for Model Number FDB241OLDC3 Dishwasher fills, empties through most of wash cycle several times the only time the wash/rinse pump runs is at very end of cycle one time. So only rinses once that's it. So both the pumps work, it's like the wash/rinse pump isn't being told to run. .... Controller board? John
1 Answer Hello John. Yes, you will need to order and replace the control board on the unit. Read More...
Ken July 20, 2015 for Model Number FDBB2455FB1 Yesterday we had a brown out today I have no lights on my washer and will not turn on. I have test for power coming in and it is good checked for power coming in to control board it is good. I am thinking the control board could be the issue. any suggestions on what else it could be and how to check it?
1 Answer Hello Ken. If there is power coming in, but will not come out, you will need to replace the control board on the unit. Read More...
Mike T May 01, 2015 for Model Number GLD2445RFC2 Dishwasher shuts down approximately 41 minutes into the cycle. Gives "PF" code. Technician replaced control board and checks junction box . Same symptom. I watch closely while running through cycle with a fluke meter attached recording min/max voltages. Starts out running initially at 123 volts. By the time we get to 41 minutes into the cycle voltage is now around 119-120. dishwasher stops and power fail code displays. Lowest recorded voltage is 119.3 volts. Did not have an amp clamp to see what the amperage draw was but suspect it was climbing as voltage was dropping. Suspect the motor is drawing more amps as it heats up and or runs longer. Control board probably has a tolerance range for amp draw and shuts down dishwasher when that is exceeded. Any help for this problem? Must be something other than control board since a new one did not solve problem thanks mike
1 Answer Mike, You will want to check the pump to make sure that there is nothing clogged in the pump that would cause more drag on the motor which would cause a higher amp draw. If this checks ok then the circulation pump is the most likely cause for this failure. Read More...
Mike March 16, 2014 for Model Number GLD2440rec1 This morning the dishwasher worked fine.. you select or leave the button on for light wash and it went right to the 86 and started and counted down from there...... now this evening we first got no lights and then tried all the buttons and still nothing.. then by chance I held the rinse and hold and the unit started working by counting up from 1 to 8 and then the clean and sanitize lights come on..... tried light was button again and nothing....so I reset the breaker switch.... went back up and this time the full wash and the 96 number was lit and hit the start button and it went out and then the sensing light came on and it went into the rinse and hold cycle again......... is this a control board issue and what is the part number and how hard is this to replace ?? thanks
1 Answer Mike, With the unit coming up with a display only working sporadically but the unit not working then the control board 154663004 would be the issue. To access the control board you will need to remove the screws on the top inner door to remove the control panel. This will give you access to the control board. Read More...
Bob K March 10, 2014 for Model Number GLD2445RFSO Frigidaire dishwasher This dishwasher is about 6 years old. Started to leak a small amount of water from the right side of the door. The amount is maybe 1 or 2 ounces during a normal cycle. In checking, the gasket looks fine, but that side of the door, when closed really isn't in tight against the top. Seems to be something binding, or the door makes contact at the seal at the bottom first, to the point it keeps the top of the door from making good contact. The left side of the door seems fine. I know I could shim the latch mechanism out a little, but feel this really isn't fixing what's wrong. Any suggestions as to what to look for?
1 Answer Hello Bob. The first thing you will need to check is the levelness of the dishwasher. If it is not level, the door will not close properly. On this model, usually the correct way to repair the unit is to replace the lower door seal and the splash guards in the unit. Read More...