Eli February 15, 2014 for Model Number frigidaire gld2445rfb0 My Frigidaire gld2445rfb0 is flashing CL and will not function. Previously, it flashed CL but stopped after five minutes and functioned normally. In addition, a few months ago the touchpad began acting oddly. The latch and seal seem to be working. I think I need to replace the control panel or touchpad. I think it will be the control panel. The unit is six years old. Just wondering if my assessment seems correct and if I should replace the dishwasher rather than buy a new control panel.
1 Answer Hello Eli. Make sure the wires are good and if so, replace the door latch assembly 154529401 on the unit. Read More...
Earl October 26, 2013 for Model Number GLD2445RFCO We have power to the dishwasher but it do not work, flashing light on the control panel (CL).
1 Answer Hello Earl. You need to try to unlock the control panel. If it will not unlock, you will need to replace the control board 154663004 in the unit. Read More...
Jerry July 08, 2013 for Model Number GLD2445RFBO My dishwasher stops erratically through out the cycle and flashes power failure? Is the control board bad or is there something else I should check. thanks
1 Answer Hello Jerry. Look for a loose connection. If none is found, replace the control board on the unit. Read More...
Jerry March 21, 2013 for Model Number GLD2440REB1 Have trouble selecting wash cycle and options. Depressing touch pad display does not always activate lights. In this most recent event it was stuck on "Pots & Pans" . After repeated attempts of opening/closing door, hitting start/cancel button and "Normal Wash" and "No Heat Dry", we got it working. Is it a contol panel problem? Is it difficult to access and change out?
1 Answer Hello Jerry. Yes, you will need to replace the control panel. They are not to hard to replace on the unit. Read More...
Nick February 27, 2013 for Model Number gld2445rfco Are there instalation instructions included with part # 154663004. Is this part fairly easy to install?
1 Answer Nick, The part does not come with install instructions. To install you will need to remove the screws that hold the inner liner in place. Once removed you will have access to control panel to remove control board. Make sure that the unit is disconnected from power before doing this. Read More...
George March 13, 2012 for Model Number frigidaire dishwasher fdb2415lfbo I have power to the unit but I have no lights on the touchboard display. I checked the two leads at the door switch with an ohmmeter and got a reading of 1420. Does that mean good door switch? Do I need a control board and which number? Thanks!
1 Answer Hello George. As long as you have removed the electrical connection cover to the unit and verified voltage there and checked the connections in the wire nuts, the problem is usually in the relay/control board 154663004. I would check the connections to the switch board before I ordered anything. It can sometimes be solved by removing and reinstalling an electrical connection. If this doesn't work, chances are good the control board has failed. Realize the door switch has to be closed to achieve power to the board. Make sure the unit isn't full of water when you do this so you don't take an unexpected shower! I hope this helps you solve your issue and have a great day! Read More...
Dominick March 05, 2012 for Model Number gld2440rec1 When we pick a program like normal wash and hit start, the dishwashers goes to code CL in which means close door the door and latch both are closed. The dishwasher has a electrical motor sound and occasionally the timer flashes 86 and back to CL. I took panel apart to check for loose connection, but seems everything is secure. Thinking bad door switch if there is one??? HELP, Thanks
1 Answer Hello Dominick. Based on the information you provided, it sounds like the latch assembly 154529401 is bad and will need to be replaced. Hope this helps. Read More...
Ed February 29, 2012 for Model Number GLD2445RFQ2 We put the dishwasher on normal cyle and it runs for anywhere from 2-8 minutes and then shuts off and flashes PF and the high temp and no heat dry lites flash. We replaced the pc bd from your site but it still does the same thing.I tested the input power at the bd until it shuts down and it never losses power to the bd. I also tried the door switched by jumping out the switches but that also didn't work. I feel as though the new bd we received is bad unless you have other suggestions. Thanks
1 Answer Hello Ed. Based on the information you provided, it sounds like the control board 154663004 is bad and will need to be replaced. Hope this helps. Read More...
Beth February 19, 2012 for Model Number FDB2415LFSO Dishwasher does not start nothing lights up when plugged in. No power. Checked breaker and plug both are fine. No apparent loose wires on bottom. Please help.
1 Answer Hello Beth. If there is power to the unit, and the door switch is good on the unit, you will need to replace the control board 154663004 in the unit. Hope this helps. Read More...
Ron R. February 02, 2012 for Model Number GLD2445RFSO I'm really stumped here. I am still having a problem with my Frigidaire Gallery dishwasher. Last week I posted a question under water valve (AP4321824) and got a response that I needed a control board. I received the control board, installed it, but it did not solve my problem - my dishwasher is still not working. Here's what's happening: When I turn on the dishwasher, the display panel comes on like normal, and starts counting down like normal, but nothing happens. I hear clicking occasionally like it's moving through the various phases of the wash cycle, but that's all that's happening. I connected a multi-meter to the two wires going to the water valve and I an not getting any power there. The float switch seems to be working, but to be sure, I jumped the wires on the switch and still get nothing. Do you have any other suggestions, or do I need to break down and call a repairman? (Note: I will be submitting a request to return the control board since this does not seem to be the answer.) Thanks.
1 Answer Hello Ron. It sounds like your motor, pump, and water valve are not working, Correct? If so, the problem has to be in the wiring, door switch, or control board. If the board has been replaced, you will need to check the wiring and the door switch. Hope this helps. Read More...