Procopio February 25, 2012 I got FEF368GSA with front left big surface element not heating up what should I replace?The next right big surface element on my right hand side is heating up at max always and nothing in between. The model # is FEF368GSA. It is Frigidaire.
1 Answer Procopio, First thing to check is the wiring and the control switches, You'll need to remove power to the range and remove the upper rear cover panel on the back of the range. The right front switch is most likely "stuck" in the high posirion and will need to be replaced 316238201 and the left front switch may have a damaged wire or could have a bent contact inside and not allow power to the element 316436001. Thanks Read More...
Marty C February 10, 2012 Does a non-working duel element automatically mean the element needs to be replaced?
1 Answer Hello Marty. No, you will need to test the element 316555800 and see if it has power coming to it. If not, you will need to replace the switch. If there is power, replace the element. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ray November 26, 2011 for Model Number Frigidaire PLES389ACC Both the right front dual element and the left front double element seem to have lost thermostat control. They do work but the temperature control is not useable. For example, you can completely burn an egg on a setting of 1.5 on the left front burner but on the right setting of 5 may only warm the pan. The same setting does not repeatably produce the same heat on either burner. Is the thermostat integrated into the heating element requiring replacement of the whole element or is there a way to replace only the thermostat?
1 Answer Hi Ray. The Lt. Front infinite switch is part # 318191002. The RT. front infinite switch is part # 318191002. If you are not getting 240 vac output from the switch at the H-2 and L-2 on the low mid and high settings, you have a defective switch. Thank You. Read More...
Mr. Stanton July 29, 2011 for Model Number fefl79dqh I just bought this part from you. How do I install it. How do I get the top to raise up to install the heating element?
1 Answer Mr. Stanton, Here's some general information, that should apply to your range: Raise the main top, disconnect power the the range and open the oven door. Remove the two screws holding front of the top to the front frame and lift the top up. The elements are held against the glass by two bars,one for the two front elements and one for the two rear elements. The bar is held to the main top by two screws on one end and a tab on the other. Remove the two screws and swing the bar down.Mark and disconnect the wires. There may be a slight difference, but this should get you through the repair. Thanks and Good Luck. Read More...
Jeff July 19, 2011 for Model Number 790.96119401 Would this part work for the front dual burner on my model # 790.96119401? How hard is this to replace?
1 Answer Hello Jeff! Yes, the element part number 316555800 is the correct left front dual burner element used on your Kenmore model 790.96119401. Thanks! Read More...
1 Answer Hello Curt! If you open the oven of that appliance and look into the cavity on the top ceiling you should be able to see a few screws. Once these are removed you should be able to lift it up. If you cannot, you may want to check the back and remove the screws on the hinge. If you still cannot remove the top, you may want to visit our repair forum. The technicians there may be more able to help you remove that part. I will include a link to the forum in this message. I hope this info helps!http://forum.appliancepartspros.com Read More...
1 Answer Hello Kaushik! Yes, 316555800 is the right front dual element for your model 790.96222400. Thanks! Read More...
Scott May 03, 2011 for Model Number FEF379ACF After examining the dual element I found the ceramic rod which runs to the center of the element has a riser thing on the end this riser was broken not connected to the element and fell off with no force. First what is this part of the element? And would it cause the center element to not turn on which is my main problem?
1 Answer Hello Scott. You will want to replace the element, the part you described is called a limiter. This part is not sold separate from the element. Thanks Read More...
Scott May 02, 2011 for Model Number FEF379ACF How do you check if the dual element needs to be replaced. With a multimeter continuity test? Which posts?
1 Answer Hello Scott. If you look at the element, you will see where the burner rings come together. You will test across where ther rings com into the spade connections. If it is open, it will need to be replaced. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...