Warren S. November 01, 2013 for Model Number FES365ECD How do you remove the glass and install the element for this model? I can't figure out how to get the top to release to gain access to the element. Please explain.
1 Answer Hello Warren, A slide in unit will have to be removed from its' installed position to remove the main top. Be sure to dis-continue the power supply to the unit before beginning. You will have to remove the screws around the perimeter of the top on the sides and back of the unit to release the main top. In some cases, the knobs have to be removed to allow access to the large nuts under them. When these are removed, the control panel can be released and the screws under this panel can be accessed, (only necessary on certain series of this model). Read More...
Juan August 29, 2013 for Model Number frigidaire range part (element OEM ( AP4556791) 316555800) How can I install this part (element OEM ( AP4556791) 316555800)?
1 Answer Hello Juan. Disconnect the power and open the oven door. Remove the screws under the front lip and raise the top to access and replace the element in the unit. Read More...
Nancy July 15, 2013 for Model Number PLEFZ398ECB The two back burners basically either won't turn on; or turn on and off erratically. They also make an alarm like noise on and off. What might be the problem? Thanks for your help
Lynn K June 30, 2013 for Model Number glef379dcc Cannot control front elements, when turned on they go to the high temp, cannot adjust temp with knob, do I need to replace the element or the switch, thank you
1 Answer Lynn, The surface switches would be the cause of the unit going to high and not being able to adjust. Read More...
Annie O. February 08, 2013 for Model Number glef379dbd The right side of my Frigidaire range has the dual element. The outer element works but the inner element does not. Does the complete element need to be replaced?
1 Answer Hello Annie, If the inner element has burnt out then the entire element 316555800 would have to be replaced. Read More...
David N. December 18, 2012 for Model Number CPLEF398CCA I just wonder if my Frigidaire model number CPLEF398CCA should be PLEF398CCA which bought in Canada. Looking for replacing the heat element,dual ,9"/6", surface, 2100w/700w, radiant on the front right hand side. Is 316418400 replacing 316224300?
1 Answer Hello David! No, the model would read as what you have on your appliance- CPLEF398CCA. Yes, 316418400 (316555800) replaces 316224300. Thanks! Read More...
Gfbower November 13, 2012 for Model Number GLEFM397DSF When the control switch is off, the Left Front Element is on all the time. Is the thermostat switch on the element possibly bad?
1 Answer Hello Gfbower. Check for power coming from the switch to the element. If it is there, replace the switch in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Fran October 25, 2012 for Model Number Frigidare GLEFZ384GCA I have a frigidaire ceramic cooktop stove/oven . The inside part (smaller one) of the left front dual burner does not work. The outer burner lights up but the insdie does not. Do I need to replace the entire surface element or is it something else?
1 Answer Hello Fran, To ensure that you are replacing the proper part you want to check both the burner switch 316238201 and the element 316282100. Here are some instructions on how to test these two components.1. Disconnect power, roll the control panel forward toexpose the switch terminals and reconnect power.2. With the switch turned clockwise to the HI position,measure the voltage drop between terminals 2 and4. If the meter reads zero the switch is defective.If the meter reads line to line voltage the switch isgood. Go to step 3.3. Raise the main top and locate the two terminals onthe element where the wires from terminals 2 and 4are connected. Measure the voltage drop betweenthese two terminals. If the meter reads zero thewires between the switch and the elements are open.If the meter reads line to line voltage the element isdefective. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bob July 27, 2012 for Model Number kenmore flat top electric stove 790.96112409 The center part (single) of the double element in the front right does not work now. The outside ring works fine. When I put the switch on "single" the element light still glows. I measured the terminals with multimeter and got 230V with element on. Could not get any ohm reading on that element with Stove off at the breaker, except when I put the switch on then only the middle of the 3 terminals would give me a 44 ish ohms reading. Not sure if I used the correct terminals for readings but I presume the orange wire was positive. I'm guessing I need to replace the element rather than the switch?
1 Answer Hello Bob. If the element works on single, but not on dual, it is not the element that is bad, it is the switch. If there is power coming to the element and it does not work on any setting, then you will need to replace the element 316555800. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Walt March 07, 2012 for Model Number FEFL64DSF I just bought a replacement right front element AP3706849. The part came without wiring directions. Which wires connect to which post??
1 Answer Hello Walt. You will connect the new element 316555800 the same way the old was connected. Also, there is a wiring diagram on the unit to help you if needed. Frigidaire does not offer instructions on installing this element, so it installs as the old element was installed. If needed, you can post a question on the repair forum for the other technicians to see. Here is a link. Hope this helps. http://forum.appliancepartspros.com/ Read More...