Scott March 19, 2026 for Model Number LGHB2869TF5 So I installed this part in my refrigerator and immediately everything beeped and I had power on my front panel. As I was screwing it back in I lost power. I checked and rechecked the connections several times and nothing seemed wrong. I could then start to smell something burning. Did I just fry my front panel?
1 Answer Hello Scott, thank you for contacting AppliancePartsPros.com That sounds like something got grounded out when the module was being installed. This may have fried the control panel 5304513303. If there is no obvious damage to the wiring behind the control panel or to the module that was replaced, I would suspect that the wiring built into the door 807460060 has been damaged and the door will need to be replaced. Read More...
Scott March 18, 2026 So I installed this new part and as soon as I plugged the wires in I got power and then almost immediately I have no power. Could the front panel have been fried during replacement?
1 Answer Scott, We will need to have the model number of your unit to be able to assist. Please resubmit your question with the model. Read More...
Paul B February 22, 2026 for Model Number FFHB2740PS6A Ice dispenser will not stop dispensing ice, the only way to stop it is by opening the door
1 Answer Paul, The most likely cause for this issue will be a faulty dispenser module 242270106. Read More...
Sea P April 14, 2024 for Model Number LGHB2869TF5 In the door ice maker/water dispense, the water dispenser will not stop providing water. As in it continues to flow freely.
1 Answer Sea, Check for power to the water valve, if no power the valve is the issue. If there is power to the valve, it will be a switch or control issue. Read More...
1 Answer Frank, the dispenser guide assembly 242270106 has two wire connections to plug into the door harness. Read More...
Will October 17, 2023 for Model Number FGHB2866PF3 Based on your website recommendation of part I ordered the Dispenser Funnel Guide Assembly 242270102 / AP5788338. That fits my Frigidaire (as shown in the video). The wiring harness to include the light are not in the same location as what i removed from the fridge. Is there a work around or a different part number that has the correct wiring harness?
1 Answer Will, The module 242270106 is showing as the correct unit for your model and there should be no wiring changes. Read More...
Donald October 12, 2023 for Model Number FGHF2366PFBA replaced funnel dispencer,when you use it for water it won"t shut off
1 Answer Donald, Check to make sure that there are no pinched wires from installation at this would be a likely cause for this issue. If this is good then it may be a faulty dispenser control board. Read More...
Dueh May 22, 2023 for Model Number FFHB2740PS9A My ice maker makes ice(ice bucket is full)but it won't dispense ice. It does dispense water. I already replaced the Auger Motor part # AP5330823 and the Solenoid and yoke Assy part # AP5780907 but it still doesn't dispense ice at the door and you don't hear the Auger Motor at all when trying to dispense ice at the door.If it's the Dispenser Funnel Guide Assy, do I have to replace the entire Dispenser Funnel Guide Assy or can I replace the ice dispenser switch?
1 Answer Dueh, The dispenser funnel assembly would have to be replaced as a complete assembly. It would be more likely that this issue will be a faulty dispenser board since the water is working. Read More...
1 Answer Cole, with the power cord unplugged, the bottom cover of the user interface will have two screws holding it on that would need to be removed to take off the cover. This will expose two mounting screws for the user interface. Once the screws and user interface are removed, the mounting screws for the module can be taken out and the module pulled forward. Read More...
1 Answer Linda, unfortunately, the user interface 5304513370 is not included with the module 242270106. Read More...