Mark July 31, 2024 for Model Number 790.46592500 I have the replacement burner switch 903136-9010 in hand. This for a kenmore range 6" burner. The terminal locations are different on this switch. Wires that go to the switch are two black, one of whitch is doubled. I have two white wires and one red wire. Where do they connect?
1 Answer Hello Mark, thank you for contacting APP, There should be markings on the switch to indicate each position. The wiring for this switch is as follows: Double Black to L1 1 White wire to H1 and the other White wire to H2 Red wire to L2 The remaining single wire should go to 2-P Read More...
Cheryl April 15, 2024 for Model Number 79046591500 Hi, I have a Kenmore Model# 79046591500 and ordered Part# AP4368997 to replace the switch powering the small right rear burner. The wiring connectors are in different locations. On the existing part# 318220080 that I replacing I have 2 white, 2 black (1 is piggybacked to the adjacent front right dual burner), and 1 red wire. Can you please advise me how to connect the wires to the replacement part? Thank you!
1 Answer Cheryl, You will look at the numbers on the original switch and place each wire from that location to the same location on the new one. Read More...
Murray . May 09, 2022 Please tell me the exact length of the shaft (stem). My Kenmore range needs a l-o-n-g one, around 34mm.
1 Answer Hello Murray, the manufacturer does not provide part measurements. However, if you repost with the model number and part description/location we will then be able to locate the correct part for you. Read More...
Tom December 07, 2021 for Model Number FED300DSB I think 903136-9010 is the correct switch for the right side large burner. My unit, drop-in, has the knob, then a plastic "washer" that screws onto the switch to secure the front plate. Am I correct in assuming the metal piece with the two screws is to be screwed onto this switch in applications (situations) as mine? I do not want to order the wrong one.
1 Answer Tom, You would be correct on the way that the switch should be set up. There should also be instructions that come with the switch. Read More...
Tom November 21, 2021 for Model Number FES365ESA Frigidaire stove model FES365ESA I AM TRYING TO REPLACE MY SWITCH FOR THE FRONT SMALL BURNER. 318220080. IT HAS 7 WIRE CONNECTIONS ON IT. THEY SENT ME A 903136-9010 SWITCH WHICH HAS 5 CONNECTIONS ON IT. IT CAN'T BE THE RIGHT ONE BUT NO ONE CAN TELL ME THE RIGHT SWITCH THAT IS NEEDED. THEY ALL KEEP SAYING 903136-9010. I EVEN LOOKED AT THE 9020 BUT IT STILL HAS ONLY 5 CONNECTIONS. PLEASE HELP.
1 Answer Tom, the small burner would use the infinite switch 903136-9010 and it would be wired as follows per the manufacturer's information: double red wire on L2, Orange on H2, Orange on H1, double black wire on L1, and the remaining wire on P. Read More...
Peewee356 February 16, 2021 for Model Number 790.46602500 I am trying to replace the switch for the small left rear burner and the old switch is #318220080. It has 6 wires and the replacement 903136-9010 has only five. Do I piggyback a wire to make it work?
1 Answer The wiring diagram shows five wires on your model, Black wire on L1, Yellow on H1, White to P, Yellow to H2, and Red to L2. Read More...
William B. February 04, 2020 for Model Number 79046582501 Can this switch be used on the small left burner?
1 Answer Hello William, This switch 903136-9010 is the one recommended by the manufacturer for the small front left element. Read More...
Dan January 21, 2020 for Model Number 790.46603500 Kenmore Elite Oven 2006...replaced left rear small burner switch with 903136-9010...works ok except it's off by 90 degrees...is there a way to adjust stem so off position is at 12:00 instead of 9:00? Thank you.
1 Answer Dan, the switch would have to be rotated in accordance with the position necessary as it should have multiple ports at which to secure it with the mounting screws. Read More...
John July 24, 2019 for Model Number 790.45489501 I am replacing part 318220080 with replacement part 903136–9010. I do not question if this is the correct part, my problem is on the back of the old part all prongs are labeled L1, L2, H1, H2, and P. However, on the new part, the prongs are not in the same location and they are not labeled. The picture of the part looks just like the part in your pictures, however, like I said they are not labeled so I do not know what wire goes to which prong.
1 Answer John, H2 is going to be the terminal that has the bar stretching across the switch assembly. Directly above that terminal is L2, and then L1 is at the top of the switch. On the two-terminal side, H1 is located just above the H2 bar and the topmost terminal is terminal P. Read More...
Jamal April 03, 2019 Is it possible to replace the 318220081 (the large switch) for the small burner?
1 Answer Hello Jamal, The replacement for this switch is listed by the manufacturer as 903136-9020. This is a kit that is used in place or the original switch which is no longer available. Thank you for your patience and understanding in this matter. Read More...