Carolyn October 30, 2017 The wings on my mod.GTWN2800D1WW agitator are floppy,Want just that part,or does it come in a kit ?
1 Answer Hello Carolyn. Sorry, they only offer the parts as an assembly WH43X10034. Thank you. Read More...
Debbie M August 09, 2017 for Model Number GDSR411OT6WW 1997 ge washing machine, agitator * spin won't work. Took out softner cup, agitator cap was glued on, chiseled it off, no bolt, put strap under agitator and got it out.....Transmission rod came out with agitator. Cant get rod out , don't see any agitator coupling....What do i do now?
1 Answer Debbie, The model number listed is not showing as being a good model. If the shaft came out then this would require a new transmission. The agitator would be held on with a coupling which would be up inside the agitator which it did not release from the coupler and is why the shaft came out. Read More...
Alex M. March 09, 2015 for Model Number VWSR4100V1WW When my machine empties after the rinse cycle and starts the spin cycle it makes a noise just at the beginning of the spin cycle. How do I fix this?
1 Answer Hello Alex. It really depends on the type of noise and where it is coming from. You will need to locate where the noise is coming from on the unit. Then repair or replace the part that is making the noise. Read More...
Rock West June 04, 2014 for Model Number g.e washer mod wdsr20804wn how do I get the agitator out of my washer. it does not have a bolt in it. it has 4 plastic nobs that do not turn or pull up.
1 Answer Rock West, To get the agitator out of the unit, get a rope that will slide up under the agitator. You will then use leverage to work your way around the agitator and pop it off. There is an agitator bell under it that it clips to. Read More...
Wes April 02, 2014 for Model Number WDSR2080D5WW I noticed some 'play' and 'wabble' in my GE washing machine's agitator. I bought a new agitator coupler and replaced it, but I still notice a little bit of a 'wabble' when I grab the top of the agitator and move it manually and it still has a small amount of spin 'play' to it in both directions. I can also lift the agitator up a bit. Before replacing the agitator coupler, I could move the agitator up from the base around an inch. With the new coupler, it seems to fit a bit more snug, but I can still pick it up from the base around a half an inch. Is this type of agitator supposed to fit totally snug against the bottom or is there supposed to be a small amount of 'play'?
1 Answer Wes, You will want to double check to make sure that the agitator coupler is not moving up and down. If it is moving up and down on the shaft then you would want to make sure that the agitator coupler is fully tightened. Also make sure that the drive shaft is not moving up and down then the issue would be a faulty transmission. Read More...
Tara February 21, 2014 for Model Number VVXR1040T5WB We have a HotPoint washer model: VVXR1040T5WB but I do not see our model listed below. Will this part fit?
1 Answer Hello Tara! According to the model number supplied the agitator assembly WH43X10033 is the correct replacement and will fit your appliance. Thanks! Read More...
Ed D August 10, 2013 for Model Number WVSR1060A1WW I lifted the existing agitator out of the washer and attempted to slide this one Agitator ASM (Part #: WH43X10033) back in place it would not line up and go down flush to floor of washer. Whats the issue?
1 Answer Ed, In order to get the agitator to sit down you would have to hit the top of it or push down hard until it clips into place. You will hear a snap when locked in place. Read More...
Melanie May 09, 2013 for Model Number wjsr2070b2ww General Electic washer I replaced the coupler on my washer. I cant get the agitator to snap back on when we think its back on it eventually comes back off and floats in the washer during a cycle ran. Which part number do i need it looks exactly like PART number WH43x10033. The part number imprinted on the actual part i have is175D2102. I cant find it anywhere. Im scared to get a used one from ebay as im afraid it will not work
J.M. February 09, 2013 for Model Number S1070A3WW Does the agitator assembly (p/n AP3995147) come with the Washer Agitator Coupling Kit (p/n AP3964635) or do I have to buy this separately and, will this fit on the GE washer model S1070A3WW since this model is not showing on your list?
1 Answer Hello J.M., The agitator WH43X10033 will fit the model S1070A3WW and the agitator coupling kit WH49X10042 does not come with the agitator. Read More...
M.Smart December 23, 2011 for Model Number YBXR2070T2WW Removed agitator,bolt,coupling,paperclip, and penny.Reassembled coupling,bolt,and agitator. Agitator still doesn't work? What do I do next?
1 Answer Hi. Remove the agitator and under it is a agitator coupling kit. This is the large plastic piece that goes in between the transmission shaft and bottom of the agitator. Many times it will break away and not hold the agitator tight for proper performance. It is part # WH49X10042. Thank You. Read More...