1 Answer Glen, Both, the water inlet tube and the water outlet tubes, to or from the water tank are 5/16 in. "plastic" water tube lines. The WR17X2891 Water Tank Plastic Tube would be a good alternative part. Thanks, Read More...
Dewey February 07, 2017 for Model Number TFX28PBDBBB My water dispenser stopped working and now my ice maker tray stopped filling. Should I purchase and change this valve for both problems or is there something else I need?
1 Answer Hello Dewey, You will want to check the filter first. If it is good, then you will need to replace the valve on the unit. Read More...
Bill December 08, 2016 for Model Number TPX24PPBECC I have part no. WR57X10022. Your instructional video shows a part that doesn't look anything like the part I received. I have not looked at the back of our ref. yet. For one thing the mounting bracket does not look like it will go in the same orientation or same place as your video shows. Thank you, Bill
1 Answer Bill, The video is just for a general reference tool to show how to replace the valve. Your unit will be different because the one in the video is for a whirlpool unit. When you pull your unit out the valve will be located on the left side of the unit and there will be 2 screws holding it in place. Read More...
Francisco November 20, 2016 for Model Number TFX28PPDA Here I have water through the water dispenser, but no ice. Which valve should I change since this system has a primary and a secondary.
1 Answer Francisco, The secondary water valve would be the issue since the dispenser is working and the secondary valve will be part number WR57X10024. Read More...
Kelly M October 25, 2015 for Model Number GE TPX24BPDA BB The water dispenser continues to drip after getting a glass of water. Is this the water inlet valve(s)? If so, what is your part number?
1 Answer Hello Kelly. Remove the water line from the valve and see if it is dripping. If so, you will need to order WR57X10022 for the valve needed. Read More...
Marilyn June 30, 2015 for Model Number WR57X10022 I replaced the bracket and water valve (#WR57X10022) because I could not get water to come from the door dispenser and there was water leaking underneath the refrigerator. The ice dispenser worked fine. After the replacement of the above valve and bracket, the water is now coming out of the dispenser but there is still a leak from somewhere under the refrigerator. Any suggestions?
1 Answer Hello Marilyn. You will need to check all the water tubes for cracks and replace the one leaking. Read More...
Joseph June 04, 2015 for Model Number TFS28PPDABS Please advise of the size of the water line needed to connect this? I've been advised that this is a direct replacement, and it's short one for the fitting.
1 Answer Hello Joseph. There is no hose needed. The orange is for the line going to the filter.The brown is the return from the filter.The large white is to the dispenser,and the small white is to the icemaker.House supply goes to the threaded hook up. Read More...
Reza August 13, 2013 for Model Number TPx24ppda I have frozen water at the bottom of the freezer. It looks like over flow from the icemaker. Do I need a new icemaker or new inlet valve?
1 Answer Hello Reza, This is most likely a clogged defrost drain. You should be able to determine this by removing items in the bottom of the freezer and looking through the vent slots in the bottom of the rear cover. If there is ice inside the slots, the defrost drain is the issue. This is easily cleared with a hair dryer and a piece of weed eater line. First, remove the six screws securing the rear wall panel in position. If the bottom of it is frozen in the ice, melt it out with the hair dryer to prevent damage to the panel. Remove the panel as soon as you can without damaging this part. Now using a putty knife, remove as much excess ice as possible. When this is done, use the hair dryer directing the hot air into the drain. You can speed this up drastically by using a screwdriver. You stand the screwdriver up on the ice over the drain opening and use the hair dryer to heat the screwdriver shaft. This may not seem to be faster, but it directs the heat to the clogged area enough to clear the drain much faster than trying to blow the hot air in the opening. Once the water from the melted ice disappears down the drain, use the weed eater line to "chase" the drain line. When it hits a turn in the drain, you will have to twist the weed eater line to allow it to make the turn. Once you are satisfied that the line has gone all the way through the drain tube, (I look under the unit for the end of the weed eater line to appear), put about 1 tablespoon of white vinegar into the drain to kill any bacteria that may be causing an algae formation that will clog the drain and re-assemble the unit. Read More...
Mark July 28, 2013 for Model Number TPS24BPDABS My water dispenser works but is slow (low pressure). I checked the water pressure going into the refrigerator and it is fine. I assume a solenoid needs replacing. I see there are two different ones, either WR57x10023 or WR57x10022. Is one a more likely culprit than the other? I don't have a multimeter to be able to check them. The ice maker seems to be ok. Thanks,
1 Answer Mark, You will want to make sure that the water filter in the unit is good. If not then you would want to replace the filter. The recommendation is to replace every 6 months. If this is ok then the water valve would be the issue part number WR57X10024. Read More...
Francisco June 27, 2013 for Model Number TPX24BP The water dispenser on this refrigerator stopped working recently. I checked the line coming out of the wall through the long skinny filter and it is clear. When I press a glass up against the dispenser button, I no longer hear a motor/pump turn on like I used to. In searching the parts list all I see listed are "valves", not pumps. Am I missing something? I pulled the entire assembly with the blue valves and did not find any disconnected tubes or leaks. Any suggestions? Ice maker works fine - still gets water and makes ice. Thanks!
1 Answer Francisco, You will want to test for 120 vac when pushing the water dispenser at the water valve. If the water valve is getting 120 vac then replace the water valve. Read More...