Jonathan October 17, 2019 for Model Number WB27T10264 The transformer is blown on the control module. The oven is Sears model 911404656. If I can't get the control module anymore, can you help me with the replacement of the transformer? Thanks, Jonathan
1 Answer Jonathan, unfortunately, as the control WB27T10264 has been discontinued, we would not be able to recommend an alternative repair. In regards to the transformer on the control, we would not know of any replacement component used on this control as the manufacturer does not provide this information. Read More...
Jim B. February 01, 2016 for Model Number JKP15BW1BB (oven) and WB27K5299 (control/clock unit) I need a replacement control unit (broiler output relay does not switch voltage to element). This part is shown to be the proper replacement for my original control unit. However, the switch layout does not match my oven's current switch layout (both in number of switches and their position). How can this unit be a replacement if it's switches don't match the printed control markings on my current unit? Thanks
1 Answer Hello Jim, WB27T10264 is the part substituted by the manufacturer. It should come with any necessary instructions needed to make it operational on your model. Read More...
Maria December 13, 2014 for Model Number WB27K5299 See video repair request the WB27T10264 part that was replaced by the remmplazo AP3155966 and does not appear any video. Please send video.
Ms Sharon November 06, 2014 for Model Number JKP15WW2WW My start button does not work. I finally purchased a new control board, I installed it and it worked for about 3 weeks and the start button does not start the oven..What do you think what could be the problem... thanks
1 Answer Hello Ms. Sharon. The part you are needing to repair the unit is WB36T10138. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Benny September 08, 2014 for Model Number Jkp27wow2ww We are getting an error code F7 on our oven. It alarms constantly. The only way to stop is to cut the power. What should we do?
1 Answer Hello Benny. Based on the information you provided, the clock assembly will need to be replaced for the f7. Read More...
Ken September 02, 2014 for Model Number 911 47465791 We have a Kenmore wall oven and have now replaced the control board twice and temp sensor as well due to various error codes F7, F2, and PUSH TO START. The latter is now showing after again only having the new control board in for a few weeks. I'm beginning to think the new control board I sent back wasn't bad after all...something else is going on and I can't put my finger on it. Suggestions?
1 Answer Hello Ken. Based on the information you provided, you will need to order and replace the control panel WB36T10142. Read More...
G-Mac August 12, 2014 for Model Number JCKP15WW-1 When I touch the "oven" button to turn on the oven, nothing happens, all other buttons work fine. I have turned the power off for a while and when turned back on and press the oven button, sometimes it comes on and I can adjust the oven temperature and turn it off, but it will not come on again. Does this sound like a clock problem or a front panel issue? Thanks
1 Answer G-Mac, You will want to check the ribbon harness connection at the clock assembly. Check for loose or corroded connection. If this checks ok then the most likely cause woudlb e a bad control panel. Read More...
Terry May 15, 2014 for Model Number jkp15wow1ww This is a ge wall oven I have gotten error-7 displayed several times' shut off power to reset it and only once did it stay off long enough to use the oven. The error-7 has come back again after staying off for several days and want to know what your thoughts are about replacing the control panel if necessary.
1 Answer Hello Terry. Based on the error code, you will need to replace the control board WB27T10264 in the unit. Read More...
Jerry February 10, 2014 for Model Number jrp15b0w4bb Ge wall oven. The broiler element will not come on. The element an wiring is good. I jumped the k 3 relay an the element came on. What controls that k3 relay to bring broiler element on?
1 Answer Hello Jerry. It sounds like the control board WB27T10264 is bad and will need to be replaced in the unit. Read More...
1 Answer Hello Linda. You do not replace the clock from the front. You have to pull out the oven and remove the top panel to replace the clock in the unit. Read More...