Charles November 11, 2023 for Model Number ZEK938SM1SS The oven is set to 350 then turned on. The oven heats up to 375 before it stops heating.Then the oven temp goes down to 325 before the heating element comes on again. The oven will keep cycling between 325 and 375 forever. Is this a normal temperature swing 50 degrees? Do I need to change something? Thanks Charlie
1 Answer Charles, an oven will cycle from a higher temperature to a lower temperature to have an average temperature of the two. In this case, the average would be 350. However, while it may start out with a wide variation, it should start decreasing how much a temperature swing there is. A 50 degree difference that is constant is usually an indication of a main control WB27T10918 failure. Read More...
Sharon July 09, 2020 for Model Number JKP15WOW2WW My mom's oven will turn on and cook - but it can't be turned off with the switch on the oven - she has to turn it off at the breaker. Any idea what part needs to be replaced?
1 Answer Hello Sharon,the keypad/switch membrane/control panel has one or more faulty keypads, it is part (WB36T10138) unfortunately it is no longer available from the manufacturer, there is no substitute part. Read More...
Heather June 24, 2020 for Model Number WEG730H0DS0 My lower oven will shut off and lock. I can run it for about 30 minutes at 350 before this happens. The lower oven fan never comes on. I've had the fan and the door lock assembly replaced. It used to give code of f9 but now it's not giving any codes and I still have the same problem.
1 Answer Hello Heather,the control board should have turned on the cool fan at about 200 deg oven temp, it is needed to keep the controls at a safe temp, the control board is part W11050551. Read More...
Jason November 13, 2018 for Model Number JKP13GT1BB Hello Pros... My GE Wall oven shuts off after about 20 minutes at 500 degrees flashing code F2... I replaced the temperature sensor ( WB21X5301) but it did not fix it... I think the control panel cooling fan is not coming on... Possibly causing the board to think its over temp... Is this limit switch the one that turns that fan on? Can I test it at room temp Ohms? Am I on the right track? Thank you in advance!
1 Answer Jason, check the cooling fan limit switch, it should close and turn on the cooling fan once the temperature rises in the oven. If the switch is closed and there is voltage going to the blower, replace the blower. The part number for the switch is WB24K5033, the blower motor is WB26K5045 Read More...
Ken March 21, 2017 for Model Number GE model JRP15W0W5WW Oven would come on and then click. Replaced limit switch wb24t10076 now comes but the fan continues to run an wont turn off. Does the wb24k5085 switch have to be replaced also?
1 Answer Ken, It does sound like the limit switch would be faulty and would need to be replaced. Read More...
John March 15, 2016 for Model Number GEJKP45BW2BB When the oven is on or heating up sometimes it shuts off and the lock light flashes and the lock mech continues to cycle. I use to be able to rest the electrical breaker to resolve this issue but now I cannot stop it and have stopped using the oven. I removed the locking latch assembly only to find that the motor works fine when powered with 110Vac and the open and close limit switches on the lock assemble both appear to have open and closed conductivity when tested with an ohm meter. Could you please suggest where to go from here? Is there a door lock thermal switch or a door limit switch that could be bad? Could there be an issue with the control board? Model Number JKP45BW2BB
1 Answer John, The issue with the lock assembly would most likely be caused by a faulty control board WB27T10290. Read More...
Frank March 01, 2015 for Model Number jkp15 Oven kept turning off during roasting, kept beeping. Reset and it did same thing again. Code F0 appeared on screen so I turned off power at box. Restored power and it seemed to reset but then when back to no function. Beep occurred when I hit start pr clear pad, turned off power and left it off?
1 Answer Frank, This issue will be caused by a shorted off key. you will need to determine whether the problem is in the keypad or the control board by disconnecting the ribbon cable and measuring the flat cable pins 13 to 14. Should be to probe side with conductor. Should be 125 to 1750 ohms while pressing the off key. Read More...
Doug September 22, 2014 for Model Number jkp26gp Upper oven does not heat. The only pad reading is time/timer. Someone (don't ask) used the self cleaning cycle with meat thermometer inside. Yes, there was a violent explosion, but the oven continued to work for awhile.
1 Answer Doug, With the upper oven not working, either element the issue would be with the control board on the unit. Read More...
Chris December 03, 2013 for Model Number Ge double oven zek754gp My upper oven seems to work fine both broil and bake. The lower oven does not set a code but it turns off unexpectedly. I try and set a bake temp and it turns off before reaching the set point. The broil feature does the same as the bake. When I touch the coils, they do get hot to the touch. Any suggestions?
1 Answer Hello Chris. If the elements get hot, but it shuts down, the control board WB27K5047 is bad. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
John July 13, 2013 for Model Number Sears 911.477592000 When cleaning either oven unit, can feel the surrounding wood frame get very hot. Fan in upper unit never comes on; lower unit fan seems to work OK.
1 Answer Hello John, The only fan that should matter during self clean or when baking without the convection feature is the one in the top of the unit (AP3204890). This fan is turned on and off by a thermostat and you should hear it running for some time after the unit has been turned of. Its' only purpose is to keep the on-board electronics cool. Read More...