John January 26, 2024 for Model Number JT965WF3WW The control panel for the oven portion of the microwave/oven combo is dead (blank). The microway still works and the door light to the oven still works when the door is ajar. What may be the cause? How can I diagnose the problem and repair?
1 Answer John, the wires going to the oven control WB27T10566 would need to be inspected for any damage. If the wires are good, the control has failed. Read More...
Ernest October 18, 2023 for Model Number JT912-30 My electric built-in GE profile oven suddenly stopped heating. There are no error codes and the display seems to be working fine. Both the broiler element and the bake element do not heat up. I tested both with a multimeter and they are working. I replaced the thermometer but that did not help. Is it possible it's the thermal fuse? Any other possibilities?
1 Answer Ernest,Based on the information provided It is likely an oven sensor (test for 1100O at room temperature) broken wiring or an ERC (electronic range control). Read More...
Thomas July 20, 2023 for Model Number JT915SK3SS After roasting at 400 for 35 minutes and then broiling display went blank and nothing worked. I reset the breaker and everything came back on. First time happening. Is there a problem to be looked at.
1 Answer Hello Thomas, the control may have been affected by heat from the oven, check the cooling fan is working also that the oven door is closing fully and the door gasket is sealing. Read More...
Richard September 11, 2022 for Model Number JTP15WOA2WW WHY DOES OVEN FAN RUN FOR SEVERAL HOURS AFTER COOKING CYCLE IS FINISHED? THINK IT'S ONLY SUPPOSED FOR APPROX. 30 MINUTES.
1 Answer Richard,This is controlled by a thermostat not an amount of time. Therefore you could have an issue with the thermostat or the cooling fan and or ventilation. Read More...
Jblood98 March 11, 2021 for Model Number JGSP48B0H3BB My GE profile gas range oven will preheat but once the set temperature is reached, the igniter and gas turn off and never cycle back on. So, the actual temperature steadily drops over time resulting in food not cooked properly. Example as follows: 1.Turn Oven on set bake temp to 375 2. Igniter glows red, flames light 3. Actual temp increases until it reaches set temp of 375, beeper sounds. 5. Igniter turns off, flames go out. 6. After 10 minutes, the actual temp has dropped to 325. Igniter comes on but flames do NOT light*** *** If I open and close oven door, the flame will relight almost instantly. The oven will heat to set temp but then the temp will steadily drop again. What I have done so far: -Replaced igniter. -Replaced Temperature sensor. -Measured 3.25 - 3.28A current flow through igniter wire using clamp on ammeter (when igniter lit). -Replaced Control Board. Other observations: - Initial ignition occurs but seems to take longer that expected (i.e. 3-4 minutes). -Preheat time is normal
1 Answer jblood98,Based on the information provided and the parts already replaced it sounds like a gas/safety valve assembly would likely be the issue. Read More...
Larry October 28, 2020 for Model Number GE Profile Built In Oven PT916WM1MM my oven starts cooking and stops in the middle of the process. Nothing will work until I flip the breaker and reset it, then it continues on. I replaced the control board and I’m now thinking about replacing the thermo limit switch. Any advice?
1 Answer Hello Larry,check if the oven door is closing and sealing especially along the top of the door gasket, it sounds like heat/moisture may be affecting the control panel. Keep in mind by cycling the power to the oven all you are doing is resetting the control board. Read More...
James October 23, 2020 for Model Number JCBP24WK1WW The oven will continue to heat after reaching the desired heat and will only stop when shut off. I have already replaced the sensor part# wb21t10007
1 Answer James, You will want to test the oven sensor for a resistance of 1090 ohms at room temperature and also at 350 should have 1654 ohms. If the sensor checks ok then this will be a faulty control board WB27X45466 that has a sticking relay. Read More...
Anthony February 27, 2020 for Model Number PCS968DP2BB Our GE Profile oven keeps giving us an F9 code after we are using the oven over 400°F or when we set to broil. I have changed out the door locking mechanism and the control panel also can see the fan working and no blockage to the vents. I am thinking it could be the limit switch but don't know if that would be the problem. Thanks
1 Answer Hello Anthony, You should use a test meter to see if the limit switch WB24T10060 is open. If it shows continuity, it is good and the problem will most likely be the control WB27T11151. f it reads open, (no continuity), it is bad and will most likely correct the issue. Read More...
Eduardo February 13, 2019 My GE JKP15B0A1BB oven Both the bake and boiler elements will not work(heat}. Control panel works. Clock, oven light, keyboard control up an down heat. I press the bake button set to 400 no heat just stays at 100. I do hear a click like it trying to raise the heat. So I tried the boiler and it would not heat either. Thank
1 Answer Eduardo, You will want to set the oven to bake or broil and test across the elements for 240 vac. if there is not proper power present then this would be a faulty control board. Read More...
Eduardo February 13, 2019 My GE JKP15B0A1BB Oven stop working No heat on bake, broil, or self cleaning
1 Answer Eduardo, For this issue the most likely cause will be a faulty oven control board WB27T10276. Read More...