Phillip September 04, 2014 for Model Number ( Golden - Name brand ) (Model - GLP26R) This machine does not have a standard agitator but a flat impeller type. The cloth kept getting tangled in the machine. this in turn causes the machine to be of balance in the spin cycle. this happens every load. It appear as if the machine spins about 180 degree before it reverse in the other direction. Normally it should just go back and forth about 90 degrees. thanks for all your help.
1 Answer Hello Phillip. Sorry, we do not offer parts or have any information on this unit. Read More...
Phillip August 31, 2014 for Model Number GTWN4950LOWS The wash stays in the diagnostic mode no matter what I do. The motor is in the standby mode nothing happens. no water comes in nothing. I took the plug out and still nothing, thank for all the help.
1 Answer Hello Phillip. Based on the information you provided, the board WH12X10475 is bad. Read More...
Aaron July 26, 2014 for Model Number GTWN5050M0WS I start the washing machine and it washes the clothes. It stops at the drain and rinse cycle. I unplug it and plug it back in and then it finishes the rest of the cycle. I get the 10 blinking code before i reset it by unplugging it. I have tried do the reset where you unplug it wait a minute and then lift the lid 6 times. Still stops at the drain and spin everytime until I unplug and replug. What could cause this.
1 Answer Aaron, You will want to pull the front panel off the unit and check the invertor board on the motor for the flashing LED. It will flash in a sequence and based on the sequence will tell you what the error code is per the tech sheet. You will want to replace the part that is showing as having the error code. Read More...
Mary July 17, 2014 for Model Number GTWN4950L0WS My start button doesn't work. It used to, but I how would have to press it several times for it to start. Is it the control panel or can I just replace a switch?
1 Answer Hello Mary. Based on the information you provided, you will need to order and replace the control panel on the unit. Read More...
Krystal June 30, 2014 for Model Number GTWN5050M0WS My GE washer suddenly stopped working. It beeps twice about every 20 seconds along with the Fill light blinking but nothing happens. The red light on the motor blinks 10 times, then stops, blinks 10 times again. We read online that this means there is a communication issue between the motor and the control panel or timer (I don't think my model has a timer, it was purchased new in 2011). We thought it was the lid switch (sensor) at first and replaced that but that did not fix the problem. I cannot afford a GE repairman and do not want to spend anymore money on parts that are not the issue. Does this sound like we have to replace the entire control board or is there a simpler fix? I have been looking everywhere for this answer. Thank you for any help.
1 Answer Hello Krystal, As per the tech sheet this is a Communication Error. Check connections on the control board. If this does not produce positive results, replace the control WH12X10475. Read More...
Aries April 14, 2014 for Model Number GTWN5050MOWS I found a smelly dead lizard in the control board and tried every single suggestion. I'm thinking the worst and it fried my board. I'm thinking of resodering and replacing the resitors. Is this ok to repair or replacement is the only option?
1 Answer Hello Aries. It is best to replace the board. The manufacturer does not sell any parts to repair the boards. Read More...
James March 10, 2014 for Model Number GLWN5050MOWS #1 Does anybody really answer these questions? I sent in a request two or three days ago and haven't heard back from anyone. #2 The washer will not advance into the wash cycle or spin cycle, the lid switch has been bypassed so that isn't the problem. The belt is in good shape and tensioned correctly, the drum spins freely by hand so it isn't frozen on the shaft or bearings. It fills to the proper level so it is not the fill valve or fill switch. The drain pump works fine so the last thing I can come up with is the control board has gone bad. I unplugged the machine as it says to reset the electronics but that didn't help either.
1 Answer Hello James. From what you are describing it does sound like you will need to replace the control board part# WH12X10475 Read More...
Deborah December 31, 2013 for Model Number GTWN4950LOWS GE Washer: The washer will go thru the wash and rinse cycles. It will not switch over and spin. It repeatedly washes and rinse. It did this all night long before I realized it. I had to manually switch it to spin and it spun. I tried to do a normal wash cycle again and same thing.. will not spin. I've been told to replace the motor. I'm flabbergasted as I purchased this washer Dec. 2010! My previous washer was a kenmore and it lasted over 10 years.
1 Answer Deborah, At this point, it doesn't sound like you'll need a motor WH20X10066, or a motor control board WH12X10475 your washer doesn't have one. What you may want to do is unplug the power cord, open the control console (remove 4 screws along top of control panel) and retrieve the tech data sheet inside. You'll want to conduct the Field Service Mode test. This will help pin point the area that we need to concentrate on. Or if you could repost your question, and have an e mail address attached, we can probably supply you with illustrated information to help you out. Read More...
Lance September 26, 2013 for Model Number GTwn5050mows My washer wont fill. The green light on top is blinking. It is beeping as well. I checked the lid switch , and it had continuity when closed. There is also a red light on the motor that is blinking 10 times then repeats. There is no fuse. What could causing the problem?
1 Answer Hello Lance. It sounds like the board WH12X10475 is bad. You will want to check the water valve as well on the unit. Read More...
Win J January 03, 2013 for Model Number GE: GTWN4950LOWS Our washing machine is full of water, and stuck in the soak cycle. Is this likely a control board issue?
1 Answer Hello Win, This sounds more like a lid switch WH12X10334 failure. If the lid switch is bad the unit will start cycle. It will fill with water but this is all it will do. Read More...