Brian F July 24, 2016 for Model Number GTWN4950L0WS The washer fills and empties, the agitator moves freely and the belt is in great shape. During the cycle the motor will move the drum a quarter turn then pause for about a half minute and do it again repeatedly, occasionally doing a full turn. Does the same thing during the spin cycle. It does not agitate or do the spin cycle. I assume the motor is ok because it cycles without noise, I replaced the door switch and it still does the same thing. Is the circuit board spent? I assume it is not cycling correctly because the commands the motor gets from the board is incorrect. All connections look to be ok in both sides. Any ideas?
1 Answer Brian, This issue sounds like it would be a inverter board issue with the motor. You will want to pull the front panel off the unit and there should be a flashing light on the motor board. Count the number of flashes as this would be a error code. On the inside of the control panel there will be a tech sheet that will tell you what the number of flashes mean. Read More...
Martin B April 14, 2016 for Model Number GTWN5050M0WS My machine stopped working and the Service Mode test showed "Error Code Thermistor" and "Error Code No Fill" Replacing the water temp sensor only eliminated the thermistor error. The fill solenoids still get no voltage with the fill light blinking, nor when they are supposed to be active during the Service Mode test. Also, the plug draws an arc every time I plug it into the wall outlet. There is no Inverter Board Status Indicator light visible anywhere at or near the motor with the front panel off, even with the utility room pitch dark. Even if it is up under the splash shield on the motor that partly covers the plugs, a red glow should be illuminating the plugs, no? At age 80 I can ill afford a $75 service call. That said, how expensive will it likely be to fix this machine? (I bought it used for only $75 in 2011)
1 Answer Hello Martin. If there is no power to the valve even in diagnostic mode, then the board is bad and will need to be replaced on the unit. The spark is normal when plugging the unit into an outlet. Read More...
Phil January 02, 2016 for Model Number GE GTWN5050M0WS My washer got flooded and the motor was completely underwater. Now when I turn it on to fill it says filling but the valves don't open.
1 Answer Hello Phil. Anytime there is a flood, it can damage several of the parts. You will need to check the motor and the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Randy November 12, 2015 for Model Number gtwn5050mows GE washer How do I replace the motor control board?
1 Answer Hello Randy. Remove 4 screws across the top of the control panel. Flip control panel and access control board. Once removed, you can access and replace the control board in the unit. Read More...
Sandy November 04, 2015 for Model Number GTWN5050M0WS My washer quit agitating and spinning. I unplugged the washer and replaced the lid switch, but when I tried to plug it back in, the plug sparked. My handyman tried unplugging electrical connections in the washer and when he unplugged one on the motor, it no longer sparked. We replaced the motor, but it still sparked when we plugged it in. We think we need to replace the control board, but I thought I would ask if this is the best option.
1 Answer Sandy, Yes the control board would be the most likely cause for the unit sparking when plugging the unit in. Read More...
Ansley August 03, 2015 for Model Number GTWN5050M0WS Is there a way to confirm that I need to replace the control board? I have tested the lid switch, pressure valve, all with ohms tests. Multiple tests on the motor, fuses etc. The red light did flash 10 times and then I unplugged opened and closed the door 5 times but all that seemed to do was reset the light to blink normally. Is there any easy diagram that may help? Thanks
1 Answer Hello Ansley, The code you described is for a communication error. If no bad connections are located, replace the control WH12X10475 in the backsplash. Read More...
Bill July 12, 2015 for Model Number gtwn4250mws 080311 The washer will not wash or spin the washer beeps when filling and stops beeping when full. There is a 10 flash code on the inverter board what part do I need and is there a way to check the motor now
1 Answer Hello Bill. Based on the error code you have, it sounds like the motor WH20X10066 is bad and will need to be replaced on the unit. Read More...
Mike P February 13, 2015 for Model Number GTWN4560LOWS Our washer frequently (66%) gets stuck in an endless loop of rinse & spin. how can we fix this?
1 Answer Mike, With the unit continuously rinsing and spinning, this issue would be caused by a faulty main control board which is part number WH12X10475. Read More...
Nancy December 13, 2014 for Model Number GE gtwn5050mows About a month ago my washer would not fill with water, but would beep a lot. I checked the diagnostic code. It was blinking 10 times, so I ordered control panel WH12X10475. I just installed it and it still isn't working. Instead of continuously beeping, it just beeps once. It won't spin or fill or do anything. I rechecked the diagnostic light and it blinks continuously, so there isn't a usable code. This is for a GE washer GTWN5050MOWS.
1 Answer Nancy, Either the control board that you received has a fault with it or the inverter board on the motor would be the issue which would need to replace the motor. Read More...
Roger October 27, 2014 for Model Number GTWN5050M0WS I had a serviceman come out to check the problem of my machine which stopped running somewhere in the cycle. There was not water in the machine, but clothes had clearly been wet. Serviceman shorted mag switch leads on lid switch to each other to close that circuit (after unplugging machine.) Then he plugged in, pressed start and watched the LED flashing on the inverter on the motor and got 10 flashes which would nominally indicate the control board assembly. I am an electronics specialist myself, and I noted that the asterisk on the service sheet inside the machine for a 10 flash does indicate the control board, but if that doesn't fix it, it says "replace motor". Motor does not look or smell burned. But control panel has no burns on it either, and the logical place to look --- the 3 coil relays all indicate 400 ohms -- so they aren't burned either. The rest of the board(s) makes too much time to try to fix. QUESTION: HOW LIKELY IS IT THAT IT IS THE ($94) BOARD? AND IF NOT, HOW LIKELY THAT A MOTOR WOULD FIX IT, AND IF SO AT WHAT PRICE AND HOW LONG? THANKS (I KNOW THIS IS A DIFFICULT ONE!)
1 Answer Roger, The reason the manufacturer put the main control board down first is because with this inverter it is detecting an issue with the control board and is programmed to put out that signal for a fault in the control. On a off chance it could be that the inverter board is corrupted in its error codes but the control board would be the most likely cause. Read More...