Paul May 03, 2025 for Model Number GFW550SSN0WW I’m getting all kinds of codes that deal with water. I did all the diagnostic test and everything is working. When I go to wash my clothes it’s all good until the washer changes to the wash cycle. Then it stops and shows “end” on the screen.
1 Answer Paul, Thank you for your question. If the unit is giving error codes and it works properly in the service diagnostics, then this will be a faulty control board WH22X38697. Read More...
Douglas April 27, 2025 for Model Number GFW550SSN5WW The washer will not spin on the first , second, or third spin but will on last. I have to do a extra rinse to get clean. Is it the control board?? And part # would that be.. thanks..
1 Answer Thank you for your question Douglas. While it could potentially be an issue with the main control WH22X38697, checking for any error codes would be recommended. This can be done by holding the start button down for 10 seconds while the unit is in standby. After 10 seconds, the LEDs should all turn on and the start button can be released. The pause and door lock LEDs should then constantly blink while any error codes should show up. Read More...
Michelle September 07, 2024 for Model Number GFW550SSN0WW The unit is not receiving the message to lock the door. So the unit will not run. It can be manually locked after the cycle is started , so the the door lock itself works. The washer will run complete cycles also. It will not receive the signal to unlock either. It has to be unlocked manually. Control board?
1 Answer Michelle, if there is not an indication of loose or damaged wires, this failure would most likely be caused by the main control WH22X38697. Read More...
Brandon February 15, 2024 for Model Number GFW650SPN0SN We have been gone for a week and come home and went to wash clothes and there is no power showing on main controls. No lights on and seems to be dead for power. I would like to replace the main control board to fix problem. Is this a good solution?
1 Answer Brandon, the main control WH22X37840 would need to be tested for 120VAC at connection J101. If there isn't voltage, the power supply may need to be checked to ensure there is power at the outlet. If there is voltage, the connection J615 would need to be tested for 12VDC from pin 1 to pin 3. If there is not voltage, the main control would need to be replaced. If there is voltage, the user interface would need to be tested for 12VDC on the same wires at the user interface. If there is voltage present, the user interface WH22X34918 has failed. Read More...
Mont September 06, 2023 for Model Number GE GFW550SSN2WW When I run the error tests, the number 12 test, which is the one for the pump on this unit, the whole display goes black and never comes back on. I don't know if that indicates the board has a problem. When I run the test 14 for the spin test, the display goes black, but eventually the drum starts spinning, but I never see anything happen on test 12. During the time that the pump is supposed to be running, when I test the board for output on pins 2 and 3, there is no voltage. When I disconnect that plug from the circuit board and do an ohms test, I get 20.4 ohms on the pump motor. The manual says it should be approximately 19.5 ohms. I do a lot of service work on dairy equipment electronics and pulsator coils. If a pulsator coil was off that approximate value of .9 ohms, we would say that was within tolerance, but I am not sure if that applies to this pump motor. When I opened the pump, there was a small wire on the floor. I am not sure if it came out of the pump, but I think so. If so, that may have been stopping the pump. I used a cord and applied 120V to the pump motor, it seemed to run fine so I think the pump is probably OK. Would you recommend that I change the pump too?
1 Answer Hello Mont, likely the drain pump had a failure at some point and damaged the circuits in the main control board, at this point both the pump motor and the main control board should be replaced. Read More...
Lee May 19, 2023 for Model Number GFW510SCN3WW I am getting an error code 31 and the unit will not work. Will replacing the main board resolve the error code?
1 Answer Lee,Check the door lock, door switch, and water temperature sensor. Check harnesses and connections.• If the above is checked well, replace the main control board. Read More...
Mike May 19, 2023 for Model Number GFW510SCN3WW I am not getting voltage to the motor on my washer. How can I tell if I am getting power from this board to the motor?
1 Answer Mike, the main control WH22X38697 would communicate with the motor inverter control WH22X38837 when the inverter would need to operate the motor. There is a 120VAC supply that would go from the main control connector J506 to the inverter connector J101. There will also be 12VDC communication signals from the main control connector J101 to the inverter J301. If the main control is failing to send either voltages, it would need to be replaced. Read More...
1 Answer Mike, the pressure sensor of the main control WH22X38697 would not have a testing procedure aside from what can be identified through a diagnostic mode or through the process of elimination. Read More...
1 Answer No, but you can Text “PARTS” to 36534 and follow the prompts to get a copy of the instructions electronically. Read More...