Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Main Control Board by Ge

Best Seller
Manufacturer Part
4.89 (64)
By: Ge
Part Number: OEM24164106
Manufacturer Part Number: WH22X38697

Fix no power, blank display, or continuous drain pump issues. This main control board coordinates wash cycles. Moderate DIY repair, 1-2 hours.

More
$153.95

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Ge Washer Main Control Board (Part Number: OEM24164106)

Paul for Model Number GFW550SSN5WW

Try this again ?? the machine first started having an issue when it was not drying the clothes like it used to in the spin cycle, it was leaving two minutes left on the spin cycle and would stop spinning, no visible water in the tub. Did every step in the troubleshooting part in the Manuel, check the pump filter, drain hose etc. Found no issues. Put a cleaning tablet in the machine. Then ran a full cycle normal high heat. Everything seemed fine. Did two loads of wash this past Friday and everything worked normal. Sunday evening at 9 PM I hear the machine turned on all by itself. It was in a drain cycle. I could hear the pump and the drain hose pumping into the drain, I did not hear any water coming out. CANCEL was going across the screen. Tried hitting the power button and the play pause button. Nothing worked so I unplugged it. There it sits. There are no visible signs of leaking water anywhere. The only issue that I have seen with this machine since owning it is that it likes to dance around a lot. My sister had the exact same machine and she said the same thing. The machine is perfectly level. I have checked it multiple times and yes, I know how to use a level. Thoughts. Thank you

1 Answer

Thanks for going through all that again! That detailed explanation helps quite a bit, especially the part about the washer turning itself on and running the drain pump with CANCEL scrolling across the display.

On your GE GFW550SSN5WW, I think we may be dealing with two related issues, but I wouldn't replace any parts just yet.

The first issue, where the washer stops spinning with two minutes remaining, could be caused by an unbalanced load, excessive vibration, or a problem detecting that the water has completely drained. Even though you don't see water in the tub, the control may still be receiving an incorrect water-level reading.

The second issue is more interesting. The washer turning on by itself and running the drain pump could indicate that its flood-protection or water-level monitoring system was activated. Some GE front-load washers will run the drain pump when the control detects an abnormal water-level condition. A pressure-sensing problem or a control issue could potentially explain both symptoms.

Here's what I'd like you to try next.

1. Check the pressure-sensor hose. With the washer unplugged, inspect the small hose running from the tub's air chamber toward the water-level sensing system. Look for kinks, damage, loose connections, or trapped water. Don't blow compressed air into an electronic pressure sensor.

2. Check for stored fault codes. Before clearing anything, we want to see whether the washer recorded a drain, water-level, or motor-related fault. Those codes could help narrow this down considerably.

3. Try an empty Drain & Spin cycle. After checking the hose and reconnecting everything, restore power and see whether the washer completes the cycle normally. Watch the final two minutes and listen for the drain pump. If the pump runs continuously or CANCEL appears again, stop the test.

4. Check the suspension. Since you mentioned that the washer tends to dance around, I'd also inspect the shock absorbers, suspension springs, and counterweights. A washer can be perfectly level and still vibrate excessively if the suspension isn't controlling tub movement properly.

One important precaution: If the washer starts running its drain pump unexpectedly again, unplug it rather than allowing the pump to run continuously.

I have three questions that will help us narrow this down:
1. When the washer stopped with two minutes remaining, did it display an error, or did the timer simply stay at two minutes?
2. When it turned itself on Sunday evening, was the display showing only CANCEL, or was there also an error code?
3. When you say the washer dances around, does it actually move across the floor, or does it mainly shake and bang during high-speed spin?
Based on what you've described, I'd investigate the water-level sensing system and stored fault codes first, followed by the suspension. The unexpected drain-pump operation is an important clue, and I'd rather follow that evidence before recommending a main control board.

Read More...
Paul

Hello.. ok, so I checked the filter on the bottom of the machine, twice now, I have also checked the drain tube, and made sure it is flowing water, everything checks out fine. There was no visible water left in the tub after the spin cycle when it was still showing 2min left. I ran a cleaner through it, and did a full cycle, normal mode, and everything seemed fine. Did two loads this past Friday and everthing worked as normal, however tonight, Sunday, while watching tv with my wife at 9pm in here the drain pump kick on!!! I asked my wife if she had put in a load of wash, NO!!! I ran into the room and the machine was flashing CANCEL. Hit the power button, nothing happens, hit the play/pause button, nothing. I unplugged it from the wall. Glad I was home. Thoughts? This machine has always wobbled a lot since we purchased new. It’s perfectly level. I have the dryer stacked on top of it. But the amount that it moves during a wash has always concerned me. We don’t overload it, I’d rather do an extra load than overload the machine.

1 Answer

Hello Paul, thank you for contacting AppliancePartsPros.com
We will need the model # of the appliance to be able to assist.

Read More...

1 Answer

For your GE front-load washer, model GFW550SSNWW, I recommend starting by checking and cleaning the drain pump filter. A partially clogged filter can prevent the washer from draining water quickly enough, which can cause the spin cycle to stop early or leave clothes soaking wet.
How to check and clean the drain pump filter
1. Unplug the washer from the electrical outlet.
2. Locate the small pump access door at the bottom front of the washer.
3. Place several towels and a shallow pan underneath the access area. Some water will come out.
4. Open the access door.
5. If your washer has a small emergency drain hose, remove its cap and drain the water into the pan first.
6. Slowly turn the pump filter counterclockwise to loosen it. Allow any remaining water to drain before removing it completely.
7. Pull out the filter and remove any lint, coins, hair, or other debris.
8. Rinse the filter under warm running water.
9. Look inside the filter housing with a flashlight. Check for anything blocking the pump impeller. It should be able to move, although some magnetic resistance is normal.
10. Reinstall the filter, tightening it securely, and close the access door.
After cleaning: Run a Drain & Spin cycle with a few wet towels inside the washer.

If the washer drains completely and reaches full spin speed, the clogged filter may have been the problem.

One detail specific to your GE washer: It has a fold-down pour spout behind the filter access door, rather than a separate emergency drain hose. GE's instructions are available here: GE pump filter cleaning guide and video.

Cleaning a Pump Filter
+1




If cleaning the filter doesn't correct the problem, check the drain hose for restrictions and try a Rinse & Spin cycle with an empty drum to see whether it reaches full speed.

One question: When the washer stops spinning, is there still water sitting in the drum, or does it drain completely but leave the clothes soaking wet?

That will help determine whether we're dealing with a drain pump problem or something preventing the washer from reaching full spin speed.

Read More...

1 Answer

’d start simple and not worry too much about all of those stored error codes yet. Since it first filled and stopped with water still in the drum, and now it only stays on for a few seconds before shutting off, I’d start with the drain system and water-level sensing.

First, unplug the washer and clean out the drain pump filter behind the lower access door. Make sure there isn’t a coin, lint, small sock, or anything else blocking the pump. Also check the drain hose for any kinks or restrictions.

Next, check the small pressure hose that tells the washer how much water is in the tub. Make sure it hasn’t come loose, kinked, or gotten clogged with soap residue. A problem there can make the washer think it still has water in it and stop the cycle.

After that, plug it back in and watch what happens. If the display comes on for a few seconds and then goes completely dark again, even without trying to run a cycle, I’d start looking more closely at the main control board or its power supply.

If you can still get into diagnostics, I’d do this next:

Clear the old codes if possible.
Run the drain pump test first.
See if the washer stays powered up during the test.
If it shuts off as soon as the pump is turned on, check the pump and wiring before replacing the control board.
If it shuts off even while just sitting in diagnostics, the main control becomes much more suspicious.

With codes 40, 33, 92, 39, 50, 38, and 66, I wouldn’t replace parts based on the codes alone. Several of those may simply be stored from the washer repeatedly stopping.

So I’d go in this order:

Drain filter/pump ? pressure hose ? wiring connections ? main control board.

The biggest clue now is whether the washer goes completely black when it shuts off or if the display just returns to standby.

Read More...

1 Answer

Clay,

The most likely cause for all of the issues that you are having would be a faulty main control board.

Read More...

1 Answer

Jim,

Put the unit into service diagnostic and see if there are any stored error codes. The error codes will guide you to what may be going on. This issue does sound like the control board may be at fault.

Read More...
Sam for Model Number GFW550SSNWW

GE washer not draining water, stops mid cycle after washing and after few minutes turned off, only error code showing is 32. Sometimes the timer goes backward. I check the drain pump and has resistance of about 20 and no obstruction around the filter, pipe or pump. Control Board does not show any sign of burn marks. Does have some white powder near the left side of the board around yellow color square electronic part and resistors surrounding it. Is it a control board issue? I find it difficult to believe that door lock problem would cause these symptoms of a washer. The washer closes and open at appropriate time.

1 Answer

Hello Sam, thanks for reaching out to AppliancePartsPros.com
This could be a control board WH22X38697 issue or the door lock WH01X29528 if you are getting a 32 code when the washer fails. The manufacturer suggests replacing the door lock before replacing the control board.

Read More...

1 Answer

Hello Jose, and thank you for your question. If the main control WH22X38697 is not sending 120 Volts AC to the drain pump during the test mode, the main control would be the cause of failure.

Read More...

1 Answer

Hello Kyle, and thank you for your question. Depending on the original failure, there may be another underlying issue that the main control is now detecting. If the washer fills with water but times out and displays an H2O error, it's possible that the pressure hose is blocked, preventing the control from detecting the water level.

You can check this by removing the pressure hose from the control and inspecting it for kinks or twists. Then, blow through the hose to see if air can pass freely into the tub. If not, there’s likely a clog at the tub port that will need to be cleared.

Read More...

1 Answer

Recce,

With getting all the error codes that you are then aside from faulty wiring, the main control board would be the most likely cause for this issue.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google