Kay February 24, 2026 for Model Number GTD38EASW0WS My start button is sticking. I need to order one but I can't find the right one to order!!!!!
1 Answer Hello Kay, thank you for contacting AppliancePartsPros.com The start button itself is WE04X24719 and the start switch is WE4M416. Read More...
Ray June 26, 2024 for Model Number GTUP270EM1WW sometimes when i push washer button it starts then it stop and sometimes have to push it again some times it works fine.
1 Answer Ray, as the failure is intermittent, it is most likely caused by the button selector WH01X10591. Unfortunately, this part has been discontinued by the manufacturer and is no longer available. Read More...
Ronald June 17, 2024 for Model Number GTDP180EDOWW The inside light goes on and off with the door opening and closing. The unit doesnt start when the start button is pushed. What might be the problems
1 Answer Hello Ronald, thank you for contacting APP, The unit not starting may be one of a few different things on this unit. The Timer WE4M533 may have failed and no longer be creating a circuit, also the Push-to-Start Switch WE4M416 may be bad and no longer making contact to allow the unit to start. Additionally the Hi-Limit Thermostat WE4M137, Door Switch WE4M415, or Drive Motor WE17X22217 may have failed. If it seems like the motor is buzzing, humming, or vibrating when the Push-to-Start is pressed and held we would suspect that the motor is bad, otherwise we would need to perform voltage and/or continuity/resistance tests to narrow down the issue further. Read More...
Nancy K April 23, 2024 for Model Number DBXR463EG6WW The plastic piece that holds the on/off switch has cracked and no longer holds the switch. How do I repair?
Ad September 24, 2023 for Model Number GTD45EBMK0WS Where is thermal switch on above mentioned GE dryer model.
1 Answer Ad, The thermal fuse will be located on the heater housing located on the right side as you are looking at it from the front. Read More...
Rob September 07, 2023 for Model Number GTD42EASJ2WW Where is the thermal fuse located in ge dryer Gtd42easj2ww ?
1 Answer Rob, The thermal fuse will be located on the heater housing on the top right when looking at the dryer from the front. If the dryer will not start when you push the start button then check to make sure that the door switch and the belt switch are good first. These would be the most common causes for this issue. Read More...
Tim November 03, 2021 for Model Number GTD42EASJ2WW When i push start button the dryer will run as long as you hold button in. Switch show to be working, i have removed the tub to look at motor. the belt switch shows continuity but the dryer will start with the tub and belt removed. Door switch is working. Can the timer be the problem or a bad motor.
1 Answer Tim, This issue will be caused by a faulty motor, the centrifugal switch is not making causing the unit to not stay running. Read More...
Gary January 21, 2021 for Model Number DBLR333EG6WW I want to order a switch. Mine has 3 wires and your switch has only 2 prongs. How do I wire the third wire? Thanks, Gary
1 Answer Gary, the 2 wires that are on the same side will be connected piggyback style where they are connected to the same terminal. Read More...
Jeff January 13, 2021 for Model Number WED5300SQ0 my dryer..works when the door is open and when I close it..pushing the automatic door closer button..the dryer..turns off!!.. I have checked this numerous times.. it's backward working on me..like the switch is bad
1 Answer Jeff, a faulty door switch is a good possibility but you may want to check the switch wiring first WP3406107 Dryer Door Switch and any discoloration or distortion of the door switch assembly and connectors. You may want to view the "how-to" video attached to the door switch part number so you can easily access and check the appropriate components. Read More...
Edwin January 09, 2021 for Model Number gtdp280edoww the start button is flush to the panel and will start the dryer
1 Answer Edwin, it would be likely that either the button of the panel has become misaligned or the push to start switch WE4M416 has failed. The start switch can be tested for continuity with the power supply cord unplugged and the switch removed from the panel. If it has continuity, it has failed. Read More...