Rich November 15, 2011 for Model Number GSD3835F00WW Is part number AP4980629 sold as a kit of four roller/stud assemblies, or is the price for each? I do need to replace all four.
Tina November 13, 2011 for Model Number tz307934r 363.15479000 The white side rollers on the silver glide rollers have been broken in between the roller and the white clamp that is connected to the top rack.
1 Answer Hi Tina. If you are referring to the upper rack, the upper roller kit is part # WD12X332. 1/ea. For your model # , There are 2 different styles depending on the type of the axle. Please review part # WD12X271, and part # WD35X21038 to chose between the 2. Thank You. Read More...
1 Answer Hello Tom! Yes, the roller and stud assembly WD12X10327 will fit on your appliance. This is the top rack roller and stud assembly only. Thanks! Read More...
Home Improvement Barbie November 05, 2011 for Model Number Kenmore 363.15427000 Can you show a picture as to how and where these clip on?
1 Answer Barbie, We don't have pictures available at this time, hopefully this will be enough to get you through. You'll need a small flat blade screwdriver, and a pair of needlenose pliers. First you will need to remove the front track rack stop, at the end of the metal track. To remove the rail and wheel guides, proceed as follows:Remove both front rail guide pegs by compressing the top sections together and lifting clear from the rail guides. Slide the top basket out and clear of the rail guides. Once the rack is extracted from the rail, you'll see how the roller and studs mount an are clipped to the rack side tines. You'll use the screwdriver blade to loosen and unclip the roller stud from the rack assembly, you will then need to slide the stud and roller off the axle,molded into the side of the rack. To install the new roller stud, you reverse the process, slide the new roller stud onto the axle, turn the clip up and align the clip with the side rail of the rack, and press it onto the tine. You may want to use the needlenose pliers to insure a good tight fit on the clip rail tine fitting, but be careful, don't damage the the vinyl coating on the rack. I'm sure you'll do fine, once you start the repair. Thanks and Good Luck Read More...
Sandra October 22, 2011 for Model Number GE gsd4000n10bb Does this roller stud assembly fit on my dishwasher top rack and how many come in a pack? Thanks
1 Answer Sandra, Yes that roller repair kit will work in the upper rack assembly in your dishwasher. It will contain all four of the rollers, and you should use them all. You may want to have a pair of pliers handy to snap the stud to the rack tine properly and tight. Good Luck and Thanks Read More...
Rory M. October 12, 2011 for Model Number GE Potscrubber GSD680XX02WW Does the AP4980629 roller kit fit the TOP RACK of my GE Potscrubber GSD680XX02WW. Thank you. For the person asking about installing the new rollers. I have to expand the crimp holding the front stops on the rails in order to remove the stops. This allows the old rollers to come out. Then, replace the rollers and stops and close the crimp on the stop.
1 Answer Hello Rory. Yes, WD12X10327 is the roller for the top rack assembly for the GE pot scrubber GSD680X-71WW. the model number you provided is not a valid model number according to GE. Thank You. Read More...
Rory M. October 11, 2011 for Model Number GSD680XX02WW (GE Potscrubber) Does the AP2039174 kit fit my GSD680XX02WW GE Potscrubber Dishwasher?
1 Answer Hello Rory. No, based on the model number you provided, WD35X21038 is the correct roller and axle assembly. Hope this helps. Read More...
Larry D. September 18, 2011 for Model Number GSD700X-68BA Is this the roller and stud assembly I need to connect between the upper rack to the slide rail of my dishwasher model GSD700X-68BA? Thanks.
1 Answer Hello Larry! Yes, the roller and stud assembly WD12X10327 is the correct assembly for your GE Dishwasher model GSD700X-68BA. Thanks! Read More...
Adarsh September 11, 2011 for Model Number GE GSD500-73BA Will this work with GSD500-73BA upper rack?
1 Answer Hello Adarsh! We were not able to locate model GSD500-73BA, however, I did locate model GSD500X-73BA (with an X after the 0). The upper rack roller kit is part number WD12X10327. Thanks! Read More...
Ra September 05, 2011 for Model Number General Electric GSD1180X66WW Is Roller and Stud Assembly AP4980629 the right part for GSD1180X66WW model to replace on the upper rack?
1 Answer Hello RA. Yes, based on the model number you provided, WD12X10327 is the correct roller and stud assembly for the upper rack. Hope this helps. Read More...