Tim December 05, 2014 for Model Number 79571073010 My Kenmore Elite frig has a problem with ice maker that can make ice but can't spin and drop the ice into the bin. I tried to press the reset button under neath the ice maker for 3 seconds and it could not turn. I also tried to turn off and turn on the button with press the reset at the same time and it turned only that time. I waited for more than 24 hrs to checked back and I didn't see any ice in the bin but I saw the ice in the ice tray of ice maker. So is my ice maker bad and I need to replace it? If so, can you please let me know the part to replace it? If I decide to order the replace part, how long does it take to deliver and does it come with instruction how to replace it? Thanks.
1 Answer Tim, With the icemaker not cycling by pressing the reset button, this would be an indication that the icemaker has failed and you would need to replace part number AEQ73110205. Read More...
Bob V September 10, 2014 for Model Number Kenmore Elite 795.72053.110 w/ice maker AEQ73110205 Ice maker stopped working. It would cycle OK with test button (tray rotated and water then was dispensed into tray). When pressing frige temp and door alarm at same time with ice container removed, I got a FULL response so figured the sensors were bad and and ordered new ice maker. I replaced the unit and still no ice. Pressing door alarm and frige temp, I still get FULL (even though after replacing unit I got "E ty" response. So seems like actual ice maker is OK and water goes into the ice maker and the water that went into the ice maker doing test cycle is frozen...what is the problem? Thanks
1 Answer Hello Bob. The temp in the freezer must be 0 to 5°. If it is good, you will need to order and replace the main control board on the unit. Read More...
Mike M June 13, 2014 for Model Number AP 5675953 What kind of feeler arm does this model have and where is it?
1 Answer Mike, This icemaker unit AEQ73110205 does not incorporate a feeler arm. This unit uses optics to keep the icemaker from over filling. The arms that are below the icemaker have sensors in them and emit a invisible beam that when the ice gets to a certain level it should shut the icemaking off until it reads that it is low again. Read More...
Pat W May 13, 2014 for Model Number Kenmore Elite 795.71053.010 How do I replace the ice maker part #AEQ73110205
1 Answer Pat, You will need to remove the ice bin from the unit. Under the ice bin there are 2 screw and in the middle of the door there is a screw and then one or 2 at the top above the icemaker. Remove all of these screws and remove the complete assembly. Once the entire ice compartment assembly is off, lay on towel and remove the 2 screws at the bottom of the icemaker, one on each side and one screw that is under where the water would come in at. Once this is done you can remove the old icemaker and install the new one in reverse. Read More...
Jay April 05, 2014 Part #aeq73110205. I opened motor and found reset button. I re-assembled everything and unit cycles fine when I push the reset button but will not run full cycle to dump ice on its own?
1 Answer Hello Jay, You will need to replace the icemaker assembly AEQ73110205. There is most likely a bad sensor or thermostat in that assembly. Read More...
1 Answer Hello Bill. Make sure the freezer temp is between 0 to 5°. If so, replace the icemaker. Read More...
Don January 17, 2014 for Model Number LG aeq73110205 Can the white 1/8" rubber tube that supplies the ice tray be replaced?
1 Answer Hello Don. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Rick December 29, 2013 for Model Number LFX25976ST I'll be replacing the AEQ73110205 ice maker assembly soon. When I removed it from the fridge, there was white cloth tape holding the wires together. Do you sell this tape? What is it called in the industry? Thanks! Rick
1 Answer Rick, The white cloth tape that you are referring to is the same as you would get for taping bandages. There is not a part number for this tape as it is only there to hold the wire harness in place for ease of installing the parts. Read More...
Floresta April 24, 2013 for Model Number 795.72053.110 I have a jammed icemaker on my Kenmore (LG) french door refrigerator and I want to make sure I can remove it before I order a new one. First I removed four screws and the icemaker dropped free but is still connected by it's wiring harness. The plug, however, is behind a plastic panel that seems to be part of the inner door. I removed three larger screws (screws with larger heads) and now the panel is loose and I can get to the connector. My remaining question is how to release the retaining clamps on the connector without destroying them in the learning process. Is it the two plastic tabs on the side that I have to deal with or is it the one in the center top area? Thank you
1 Answer Floresta, So far you are doing good. The center top is the one that would need to be released. Read More...
1 Answer Hi Jaydor, The ice maker AEQ73110205 is a separate part and does not come with the cooling fan motor ABA72913408. Hope this helps! Read More...