Td January 17, 2016 for Model Number LFX31925ST/00 It appears that the ice maker is faulty with this LG Refrigerator. Some of the newer LG Refrigerators which are similar now have a metal ice maker instead of the plastic one. Can I replace ice maker with newer model ice maker (metal) and possible eliminate the problem with ice maker twisting when releasing ice. I have the 30 cubic foot LG French Door Refrigerator.
1 Answer Hello TD. No, you will need to order AEQ73110205 for the icemaker assembly needed. Read More...
Ld November 07, 2015 for Model Number Lfx25976st I need to replace the ice maker assembly and since I need to remove before ordering replacement part ( in order to determine 3 or 6 wire connection) I'd like some basic removal guidance such as, do I need to turn off water supply? How many screws hold it in place? Anything else that might hamper easy removal? Thank you
1 Answer LD, For removing the icemaker on this to change or to check the wiring, you will want to remove the panel that it sits on. When you open the door for the icemaker, there will be 2 screws under the bin, there will be one screw above the icemaker at the top and one screw in the middle that you will want to remove. Once these are removed you will be able to lift out the icemaker, auger motor and solenoid that are all on the one panel. You will be able to look at the wiring at this point and when you remove the icemaker from this panel there will be 4 small screws that will have to be removed. Read More...
Paul October 31, 2015 for Model Number 795-7203 kenmore I removed the three screws but the unit didn't release it feels like something still holding the unit to the door. Don't want to pry too hard for fear of breaking the old unit any hints???
1 Answer Paul, There are 4 small screws that hold this icemaker to the bracket, The best option with this is to remove the inner door where the icemaker is located by removing the screws at the bottom where the ice drops and the screws in the wall. The reason for this is the wiring will be difficult to get to in order to remove. Once this is removed the screw you may be missing is in the upper right side of the icemaker where the water would flow into the icemaker. Read More...
Tom September 07, 2015 for Model Number LG Refrigerator model LFX28978ST/01 Ice maker died. How do you find out whether your ice maker has a 3 wire connector or a 6 wire connector? And is the part number AEQ72910401 correct, or is it AEQ73110205 Correct? What if it has 3 wire; is it then part number AEQ73110203? Also, I see the on/off switch on the front of the icemaker unit, but where is the reset switch? Please help this confused gentleman
1 Answer Hello Tom. You will need to remove the old icemaker from your unit and look and see if you need a 3 or 6 wire. Read More...
Jeff September 06, 2015 for Model Number Part Number: AP5675953 MFG Part Number: AEQ73110205 I have had the same plastic reduction gear strip teeth twice. I'm pretty sure it happens when the ice tray is being twisted at the fullest extent and there is a fair amount of force on the reduction gear. I only need to replace the reduction gear but haven't found any schematics or sources for replacements.
1 Answer Hello Jeff, While any information we could pull would have to be done using the model number from the appliances' I.D. tag, I'm sorry but it would not do any good in this case since the icemaker is considered replaceable by the manufacturer and not considered to be serviceable. There are unfortunately no instructions available in this instance. Read More...
Nana August 25, 2015 for Model Number 79572053316 I have error code Er rF and from what I've read, I likely need an ice maker assembly kit. The ice maker is making ice, but I recall a loud grinding noise when the tray was possibly emptying into the bin. Others say they pressed the reset button on the ice maker...where is that ? When I unplug and re-plug the code goes off and stays off for about 3 to 4 hrs. I changed air and water filter yesterday after code came up. Didn't help!
1 Answer Hello Nana. The error you have is not for the icemaker. It is Refrigerator Fan Error. You will need to check the fan motor in the fresh food compartment. If it is good, you will need to order and replace the main board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John W July 29, 2015 for Model Number 79571053011 How do you remove the in-door ice maker - I only see three screws - how does the water hook-up to the ice maker? I need to check the connector for proper replacement. Thanks, John W,
1 Answer Hello John. Remove the screws and slide the icemaker back and unplug the harness from the unit. Then install the new icemaker in reverse order. Read More...
Ken July 23, 2015 for Model Number 79571053010 Can the ice tray (or mold) be ordered separately from the entire ice maker? It's the only part broken. AEQ72910401 is the original part number for the entire unit.
Jay July 10, 2015 for Model Number LFX28978SW Ice maker quit making ice. Door switch works, water to dispenser, so replaced the ice maker from your company. Easy install, hooked right up yet it has been 24 hours (as stated in the manual) - no ice. Next step idea?
1 Answer Hello Jay, If the unit is not getting below about 20°F, the cycling thermostat will never cause the icemaker to cycle. If the unit is coming down to proper temperature and has not been cycling, verify electrical connections and if no problems are found, please contact us with the units' serial number for a return/exchange authorization for the part under warranty. Read More...
Bobby B. April 19, 2015 I have a Kenmore Elite purchased around 2 years ago. It is in very good condition. Anyone out there have ideas on how to get maximum value out of it so we can purchase a refrigerator that actually works?
1 Answer Hello Bobby, We are very sorry about your dis-satisfaction and would love to help in any way we can but we didn't build the unit, do not have the model number to look up parts, and do not have a symptom to analyze. If you just want your money back out of it you can advertise it online or in the local paper and try to resell it. Read More...