Wendy June 29, 2025 for Model Number LFX25991ST The micro switch (ice dispenser( needs to be replaced. However the screw and wiring is so badly corroded, that they both crumbled upon trying to remove the old micro switch. I cannot find any information (part number etc) on replacement wires.
1 Answer Wendy, Thank you for your question. The wiring in the door is not replaceable and the only way to get it would be to replace the left side door which will be part number ADD73358215. Read More...
Matthew March 06, 2025 for Model Number 106.57702703 Would this switch be compatible with this Kenmore Elite refrigerator? It would be used for the ice dispenser. I'm having trouble finding the correct switch. Thank you
1 Answer Mathew, Based on the model, the manufacturer's part list does not show a dispenser switch separately (it may come with the module). If this is like the switch you have, you would need to make sure that it is an NO switch, and this may work (no guarantee since it is not on the OEM list). Read More...
Jarpret September 10, 2024 for Model Number Lmxc23796s/00 My refrigerator started dispensing ice uncontrollably, flapper stayed open. Would this cause by a bad switch?
1 Answer Jarpet, You will want to test the switch and if it has continuity without the button being pushed in then this will be a faulty switch. If it does not then this will be a faulty dispenser board. Read More...
Gary August 13, 2024 for Model Number LFX23961SB Ice maker fills with water, freezes, but will not dump ice. Is there a "switch" that tells the ice maker to dump ice? Also, the ice control lever sometimes will not stay down obviously telling the ice make not to make anymore ice. Lever seems to be spring loaded. I pull the lever down all the way but then it springs back.
1 Answer Gary, Check the temperature at the ice maker if it is below 8°f then you will need to replace the ice maker. The ice maker cycles based on the temperature thermistor built into the ice maker. Read More...
George May 22, 2023 for Model Number LRSC26922TT Hi. Ice is being made but won't dispense. I can see Cup flapper as well as Ice Bin flapper are opening but Auger isn't turning. (checked for blockages and it spins freely by hand). There is the normal humming noise when Cube is selected, but when Crushed is selected it is strangely silent, though the cup flapper does open. Water dispensing is fine. From what I've read it could be the ice microswitch (As there might be a separate water microswitch). Or I guess the auger motor but the symptoms regarding crushed don't seem to point to that. Any other ideas would be greatly appreciated. Thank you!
1 Answer Hello George, you will need a multimeter and check for 120vac to the auger motor when ice dispense is selected, if it is getting 120vac then replace the auger motor, if no 120vac when selected the problem will be in the main control board. Read More...
Tom July 17, 2022 for Model Number 79574025412 My Kenmore will not dispense ice when I push the ice button. It will work for water but not ice. I can take the front panel off a wiggle the switch that opens the chute and tells the motor to put ice out and it will work for a couple of times but the it quits again. Could it be the switch?
Bob April 19, 2022 for Model Number LG LFXS26973D How do I access the micro switch for the dispenser on the door? Control panel will not pull out.
1 Answer Bob, the repair video located just under the main image of the microswitch 6600JB3001C can be used to assist with accessing this part. Read More...
Stacy February 24, 2022 for Model Number LRSC26922TT My dispenser was stuck in the on position. After filling a glass of water and removing the glass, it continued to dispense water. When switching the dispenser selection to ice, it continued to dispense ice. Do I simply need a dispenser switch? Also how do I access the switch on my model? The video for the dispenser switch shows how to do it with a different brand/model.
1 Answer Stacy, the dispenser switch would need to be tested for continuity to identify if it has failed. The switch would be accessed by using a putty knife to disengage locking tabs found on each side of the dispenser cover. The putty knife will slide in behind the cover and press in towards the center while lifting up. Read More...
Jen February 06, 2022 for Model Number LMX25981SW Hello! My icemaker does not seem to be getting water, but when it tries to fill, the water comes out through the water dispenser instead. I'm not sure what part to replace.
1 Answer Jen, it would be recommended that the valve is inspected to identify if wires have been crossed. The ice maker solenoid with the 1/4" water line should have an orange wire and a white wire. The water dispenser solenoid with the 5/16" tubing should have a black wire and a blue wire. If the wires are crossed, they would need to be corrected. Read More...
Erica January 19, 2022 for Model Number LRFXC2406S How do you remove the lever on an LRFXC2406S - the video isn't applicable to this model.
1 Answer Erica, Remove the display board and then the chute assembly to get to the lever and switch. Read More...