Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Samsung Refrigerator Water Filter Housing And Tube Assembly by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM12509466
Manufacturer Part Number: DA97-01666C

The water filter head holds the water filter and connects the water lines to the water filter. Approximate dimensions: 9.5" x 9.5" x 3.6"

More

Questions & Answers

For Samsung Samsung Refrigerator Water Filter Housing And Tube Assembly (Part Number: OEM12509466)

Keith for Model Number RF4287HARS/XAA-0001

My refrigerator makes loud rattling noise when dispensing water. Also, the water flow is restricted. When I removed the water filter, the water flow is stronger and there was no noise. Note that I have been using aftermarket water filter, not the Samsung OEM water filter. But I have been using aftermarket water filter for 3 years, and this noise just occurred lately. Any idea what went wrong and how to repair? My refrigerator is about 3 years old. I saw a similar question like mine on appliancepartspros.com and there was a suggestion to replace the whole water filter housing. Can I just replace the filter head, which can be easier? I prefer the easier approach; cost is secondary. Should I try to use the OEM water filter? Please indicate the part number and instruction how to do the repair. Thanks a lot, Keith

1 Answer

Hello Shannon. Based on the information you provided, it sounds like the water filter housing DA97-13850A is bad and will need to be replaced on the unit.

Read More...
Ben for Model Number RS2630SH

I have drips of water running down the blue tube out to the back panel. It has become significant enough to wet or flood the floor locally. In RS2630SH, the white and blue tubes come out in the back panel (from under the freezer section) out of something that looks like a padded (yellow sponge perhaps) sleeve. From the same sleeve (or grommet), out comes the tube to the water tank. So the tube-routing opening is shared by three tubes (2 tubes from #4 and one tube from #6 from RS2630SH refrigerator compartment diagram). I guess I can just pull the two tubes (from and to the water filter head, #4) from within the refrigerator compartment, but I am not sure, if I push the two tubes in , they will safely come out to the back. Do you know if they will come out OK without hitting any resistance from the sponge or the other tube (to the water tank)? Supposing they will come out OK, do I need to seal the opening? Is any product (like gummy seal?) recommended? Thank you.

1 Answer

Ben,

The foam insulation will not cause a issue with being able to pulled out from the back of the cabinet wall. Just disconnect from the filter housing and replace the tubing.

Read More...

1 Answer

Sam,

The way that the water line is routed through the filter, the main supply line appears to be connected directly to the line that would go to the filter. Coming off the water valve there are 2 water lines that connect via a nut on the valve. The other line that comes from the filter will connect to these 2 lines with a split connector. That is how the filter would be routed.

Read More...

1 Answer

Hello Dobalino,
I'm sorry but this cannot work. The reason is that the icemaker fills on a timed basis. If the water line is smaller than 1/4 inch, there will not be sufficient volume of water in the 6 to 7 second fill time to fill the icemaker mold. This is important because if the icemaker doesn't fill properly, the cycling thermostat will be measuring the ambient air temperature in the freezer and will cycle before the cubes are frozen. This not only causes hollow cubes but will also cause the ice in the crusher bin to be "clumped" together by the water that is not frozen and is dumped into the existing ice. The water line to the icemaker is the 1/4 inch line and the water dispense line is normally 5/16 inch. If the water line to the icemaker is disconnected, the fill tube is most likely frozen. This is caused by either low water pressure to the unit or a failing water valve.

Read More...

1 Answer

Hello Ellie,
The response we got back from our research is as follows: Water Filter Housing DA97-06317A (includes the blue tube that runs up the back of the unit). A photo is on our site.

Read More...

1 Answer

Hello Cody,
Since the water line in the door is not listed, this means that it is installed in the blown insulation of the door and the complete door assembly will have to be ordered to get the water line. I'm sorry but this is how the manufacturer has listed the part. I would have provided you with the part number but the complete model number was not listed in your post.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google