Sam September 14, 2026 for Model Number WF42H5200AW/A2 Hello, My samsung washer model WF42H5200AW/A2 when powered on the chime is weak and short. None of the display buttons work but the dial does. Replaced the DC92-01622G-1 board and now I get error 6666. I tried the reset, but error remains. The chime does work with this new board, but I cannot use the washer with the error. I put the old board back and have the same issue. What can the issue be? The display with the buttons or is it another board?
1 Answer Sam, This issue will be caused by a faulty control board which will be part number DC92-01622G. Read More...
Paul August 22, 2024 for Model Number WF42H5200AP My washer has trouble completing the spin cycle in many different washing modes. It seems to keep resetting and trying to balance before spinning. I have recalibrated and it has not helped. However, if I stop the washer and restart it in Rinse and Spin mode, it has no trouble spinning out the clothes. What is the washer sensing in the spin portion of a full cycle that fails where using the specific rinse and spin mode is successful?
1 Answer Paul, based on the information provided, it sounds like the main control has an issue within the programming. If the spin basket rotates freely and does not have any excess play, the main control would be the most likely cause of failure. The main control used with your model would be dependent on the REV number of your appliance. Read More...
Bill February 20, 2024 for Model Number WF42H5000AW/A2-0000 The washer stops about 10 minutes in the cycle. The door unlocks and my wife has opened and closed it and the cycle will continue. Sometimes it finishes the cycle sometimes it will stops before the end. Again, opening the door and closing it will continue the cycle. Do I need a door lock assembly?
1 Answer Bill, it is possible that the door switch assembly DC64-00519B locking mechanism is not operating properly. If the door can be pressed in without opening the door and it allows the washer to continue, the locking mechanism and switches have loosened and the switch assembly would need to be replaced. If the door has to be opened and closed, the failure would be in the main control DC92-01621E. Read More...
Arman May 09, 2023 for Model Number WF50K7500AV/A2 My washer stopped mid cycle and went dark (no lights on). The door was locked in closed position. Although the lights are off, when I hold the power button for few seconds i will hear a shutdown beeping. But nothing else works. no beep from any other button and certainly no function. on converter fuse is ok. on Control board, I checked AC power from Pin#1 of CN11 and pin#4 of RY7 and i get 120v AC. I checked the power between CN7 pin 4&5 was 5 V DC. and between pin 5&6 was 12 v DC. Could this be the user interface control board? Is there a way to test that before ordering the part?
1 Answer Arman,Based on the information provided the UI would likely need to be replaced. Read More...
Steph January 03, 2023 for Model Number WF42H5200A My front load washer stopped working in the middle of a cycle and showed error code AE6. I replaced the invertor board. Now it turns on and lets me select a cycle. It locks the door and then attempts to spin and then does nothing else and no error code. What else should I try
1 Answer Steph,The AE and AE6 error codes represent communication errors between the sub and main PBAs or the main and inverter PBAs. Check each of the boards for damaged or burned spots, and check the connections between the boards for damaged wires and/or bad connections. Read More...
Steph January 03, 2023 for Model Number Samsung Front Load Washer My front load washer stopped working in the middle of a cycle and showed error code AE6. I replaced the invertor board. Now it turns on and lets me select a cycle. It locks the door and then attempts to spin and then does nothing else and no error code. What else should I try?
1 Answer Steph, if the model number of your appliance could be provided in a new post, this will allow the most accurate information to be presented. Read More...
Brittany September 09, 2021 for Model Number WF42H5200AW/A2-0000 In the middle of a cycle our washing machine stopped working. We manually drained the washing machine. I called a help line for samsung and they instructed me on how to get the door unlocked. That worked. Then we got the error AE, a communication error. We have taken the front off and check all wires and connection but nothing appears to be wrong, however plugging it back in, it turns on, no button on the display reacts to being pushed and the dial does not turn to any different cycle. Which board do I need to purchase to fix this issue or do I need to purchase both? Thank you.
1 Answer Brittany, if the wires are not broken or pinched, and the connections are secured properly, the failure would most likely be in the user control DC92-01622G. While it is possible, it is less likely that the failure is in the main control DC92-01621D as well. Read More...
Paul October 16, 2020 for Model Number WF42H5200AF/A2 Washer stops mid cycle. Not always on the same spot or the same cycle, it maybe after filling or after washing. Sometimes it will complete a cycle be it either quick or normal loads. Ohm checked the lock it checked good, replaced the main control PWB, also the level sensor. Did self clean, once without stopping (4.01 hours) The washer will sometimes fill then stop then fill again and continue to do this until the tub is full then stop completely. Press stop/start and it will fill a little more then stop again. Next time it may run the entire cycle Ran service and diagnostics and no codes and everything check ok. I'm think it's a timing issue. Is this also the user interface PWB?
1 Answer Paul, the user interface control would be part number DC92-01622G, and based on the information provided, it does sound like there is a failure in the user interface. Read More...
Frustrated May 18, 2019 for Model Number wf42h5200ap/a2 wf42h5200ap/a2 will start a cycle and then stop a few minutes later. However, the panel indicates that it is still working but the timer will not progress. I have to “pause” the unit and press “start” again to get it to go. It will do this repeatedly during every load. We have to keep checking the machine over and over again. It does not appear to be a mechanical issue. The door lock functions as it should. Water and drain work as they should. Filter is clear.
1 Answer Frustrated,You should have a service sheet on this model that will walk you thru putting the unit into service mode and checking for error codes. Usually, the tech sheet is located under the top panel or inside the front panel around the drain cleanout. The plastic housing needs to be removed to feel inside the front panel. It does sound like the problem is more electric than mechanical though leaning me to think possible control fault. But definitely start your troubleshooting looking for any error codes. Read More...
Cody May 08, 2019 for Model Number Samsung WF42H5200 Our Samsung WF42H5200 washing machine continues to rinse and spin, over and over, sometimes for hours on end. I once put it in quick wash, and at one point it said it had 10 minutes left. Once the 10 minutes was up, it went back to 10 minutes and started over. A local appliance shop says we need a new control board (?), and they are looking to find the part. Does that sound correct, and should it take several days or a week or more to find a replacement part?
1 Answer Cody, more than likely the control board would be the issue unless it is showing a specific error code. Usually when an issue occurs like this and no error code is present it is because the control board is not cycling properly. In regards to any one searching for parts, we would not know what procedures another company takes so would not be able to answer. However, if a part is on back order, then it can take time to get the part itself, but not information on it. More than likely the issue is going to be with the main pcb [DC92-01621D] rather than the user interface control [DC92-01622G]. Read More...