Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Vibration Sensor Assembly by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM16737933
Manufacturer Part Number: DC93-00278B

The Washer Vibration Sensor Assembly is essential for maintaining the stability and performance of your Samsung washer. This genuine OEM part accurately detects and manages the vibration levels during wash cycles, ensuring your machine operates smoothly and efficiently. By replacing a faulty sensor with this high-quality assembly, you can prevent excessive shaking and potential damage to your appliance. The Washer Vibration Sensor Assembly is designed to fit a wide range of Samsung washer models, guaranteeing a perfect match and straightforward installation. With its reliable performance, this sensor helps extend the lifespan of your washer, providing peace of mind and optimal functionality. Investing in this genuine OEM part ensures that your Samsung washer continues to deliver excellent washing results while minimizing noise and movement. Whether youGÇÖre troubleshooting an existing issue or aiming to enhance your washerGÇÖs performance, the Washer Vibration Sensor Assembly offers a dependable solution for a better laundry experience.

More
$93.49

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Samsung Washer Vibration Sensor Assembly (Part Number: OEM16737933)

Sadiq for Model Number WA50F9A6DSW/A2

On any Washer Option (Cycle) I put on and press start, instantly I hear the Motor and draining sound comes on. Occassionally the Machine would get into thinking Mode and the Washer Light and the Cycle Light on the Knob will Blink and that shows that the Drum is taking the Start and then the Water start coming in. This I know that my Cycle is accepted by the Machine. Also sometimes before it finishes the Cycle it shows error 8E2 on the screen and then the Machine stops. What is the problem?

1 Answer

Phil, There are still several checks to make before you replace more parts. Check the wiring harness between the new MEMS sensor and the sub PCB. Then Check the motor Winding Coil unplug the connector and read resistances at any two of the three terminals on Motor Should be 19.3O. then check the DC31-00098A / DC31-00098A Rotor Position Sensor and wiring. If all checks are OK, check the wire connections, and replace if necessary, Replace the Mems PBA if all checks are OK.

Read More...
Alan for Model Number Samsung Top Load Washer Model WA5471ABP

Samsung Top Loader. Model WA5471ABP When spin cycle begins with 7 minutes on timer, spin cycle does not complete and it returns to rinse cycle with 17 minutes on the timer. This process repeats until switched off. Washing machine is level and does not vibrate, tub looks centered when empty and also remains centered when water is put in tub to the level of the agitator. This problem occurs with any size load but DOES NOT occur if it is run without any load at all, the cycle will go past 7 minutes on the timer, will go into fast spin, drain and switch off. I have also put the machine into the test mode and the drum will reach 1030 rpm. Any suggestions would be appreciated. Thanks

1 Answer

Alan,

It would be suggested to get the tech sheet from inside the unit and run a service diagnostic mode. It sounds likely that there is an off balance issue going on but if there are any errors it will tell you where to check for the issue.

Read More...

1 Answer

Hello Davy,
The mems sensor is basically a vibration sensor. It tells the control board that the machine is experiencing and out-of-balance condition.

Read More...

1 Answer

Hello Jeff,
check that the washer is not losing power from the outlet when it blanks out and all wiring connections at the control board are in place. If all check ok replace the main control board DC92-02003A.

Read More...

1 Answer

Fernando,

Since the wiring has already been checked and there are no loose connections then this would be caused by a faulty MEMS sensor and if this does not correct then you would replace the Main control board.

Read More...
Ryan for Model Number Samsung wa48j7700

My washer (Samsung wa48j7700) intermittently fills, drains, agitates, and spins, but won’t complete a full wash. There is some inconsistency in how it behaves or when exactly it decides to stop working, but most often it stops at some point during the rinse cycle. Sometimes I get an 8C error, and other times it just stops, drains, and the time remaining stays on the readout. I have visually checked all the wires and connections underneath the tub (including MEMS sensor) and up at the control panel, and everything appears clean and connected. I then checked the voltage output at the 6 wire connector from the MEMS sensor, and all were within .5 - 4.5V DC, the red was 3.34V DC. So does this mean I need to buy a new control board? Is there anything else I should check before making that expensive purchase? Perhaps the wire harness? I’m unsure how to check for continuity in the wires when one end is underneath the tub, and the other end is up top behind the control panel. Thanks.

1 Answer

Hello Ryan,
the symptoms and fault code point to a communication problem between the mems sensor ,the user interface board and the wiring between, since you have eliminated the sensor and wiring then the user interface board should be replaced, however, to be certain we advise you on the correct board part number we would need the washer's full model number.

Read More...
Dennis for Model Number wa48j7770ap/a2

Washer fills with water for about 1 minute drains immediately and continues this cycle over and over unless I turn it off. In diagnostic mode my code is 8c2. I replaced mems sensor, I checked continuity for the harness, I checked voltage from the sensor, I replaced PCB oh, and I replaced sub PCB. I still get code 8c2 and the same thing happens when I start a cycle. I don't understand how this is possible but I pretty much wasted the amount of money it would have cost to buy a new washer.

1 Answer

Dennis, based on the information provided, as the main control DC92-01021V, user control DC92-01624K, and MEMS sensor DC93-00278B have been replaced the only other possibility would be that the terminal connectors of the wire harness DC93-00579B are not making full contact with the terminals either on the MEMS sensor or the main control. It is recommended that the wire harness is tested (with unit unplugged) for this by using a marker to mark the pins on each connection point, plugging in the connector, then removing the connector to identify if the marking comes off. If a marking is not removed, then this pin is not making full contact. The terminals will need to be thoroughly cleaned after this.

Read More...

1 Answer

Carlos,

WIth the Mems sensor having been replaced and the wiring checking ok then the issue will be a faulty main control board.

Read More...

1 Answer

Paul, TThe MEMS Sensor DC93-00278B / DC93-00278B Assy Sensor; mems Sensor, is mounted to the bottom of the outer tub, on the right side in the area near the clutch assembly switch.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google