Aaron February 01, 2020 for Model Number WF520ABP/XAA Getting rear MEMS sensor error. I ordered DC93-00278B. To replace this, do I remove the top of the washer, or the back, or both? Also, some web sites have commented that it's often a bad wire rather than a bad sensor? Is that easy to check if I have a multimeter? And if so, can I just do a wire repair without replacing the sensor?
1 Answer Aaron, the mems sensor would be accessed by removing the top panel of the washer. The wires can be checked for continuity and repaired as necessary. Read More...
Carol January 31, 2020 for Model Number WF455ARGSWR/AA-0001 Where is the MEMS sensor located on my particular model washing machine? I have the replacement but wasn’t sure of it’s location. Thank you
1 Answer Carol, the mems sensor is going to be located at the top of the tub assembly near the front. Read More...
Michael January 17, 2020 for Model Number WA50K8600AV/A2 I replaced the mems sensor (AP6033762) and the main PCB board (AP6033762) with new parts. I checked all the wires and they all ping out with a multimeter. Are there any other solutions that I need to look at? I traced the wires from the mems sensor into the middle connection on the board the display is connected to. I found that pin 2 on the mems sensor cable (orange) goes out on the pin 3 black wire to the main PCB. I didn't find any other direct connections but I don't have a wiring schematic either. What else can I do to debug?
1 Answer Hello Michael, If you could please provide a symptom, we can help you with a diagnosis. It is hard to assist with troubleshooting when we are not aware of the problem experienced. Thank you for your patience and understanding in this matter. Read More...
Chad January 13, 2020 for Model Number WA50K8600AV/AA I am having an issue where I put cloths in the washer and start the load on Normal setting and the lid locks, then the drum does it checks and there are a few possible behaviors: 1) the washer makes a beep and the drain pump starts and empties the drum and then just sits there and needs to be turned off and back on 2) the washer starts to fill with water for a minute or so then does the same as #1 above, or sometimes more rarely it will keep filling and emptying over and over 3) if in the PERM PRESS mode it seems like that helps it actually run through a complete cycle without a problem most of the time. another thing I found is that if I put only a few cloths in and start the cycle I can wait till the drum fills with water then pause the cycle and add the rest of my cloths and resume and it works fine .. if I put them all in the beginning then the above happens ... I have seen error code 8C/8C2 which is MEMS sensor when going into the stored code mode. What troubleshooting steps can I do to determine if the sensor really is bad and what else could it be if the sensor is fine? thank you !!!
1 Answer Chad, a false reading from the sensor will cause the symptoms you described. First, check the wire connections at the mems sensor on the bottom of the tub, make sure the fittings are tight and no corrosion, debris, etc. then check the connections at the main control board, for the same. If the problem persists, The MEMS sensor DC93-00278B Assy Sensor; mems Sensor can be tested at the control at the 6 wire connectorThe voltage output should read more than 0.5V and less than 4.5V with the black probe of a multimeter on the blue wire at pin 5 and testing pins 2, 3, 4, and 6. Pin 1 red wire should read 3.3V DC when tested to pin 5 blue wire. The unit will need to be in operation when performing this testing procedure so caution will need to be used. If the voltages read within the tolerances, then the issue would be with the control. If the voltages are outside of the tolerances, the issue would be with the MEMS sensor unless pin 1 is not reading 3.3V, this would be a control failure. Read More...
Michael January 08, 2020 for Model Number WA52M8650AV/A4-00 I replaced the mems sensor and ran the diagnostics. It still comes up with an 8C2 error. You mention to others to check the wires but how exactly is that done? If the wire tests ok is the next step to buy the panel? Can I return the mems sensor since that was not the issue?
1 Answer Michael, the wires would be tested from where they plug into the mems sensor to where they plug into the control and would be tested for continuity. If the wires check good, the next step would be to replace the main control DC92-01998C. Unfortunately, as the mems sensor is an electronic part and has been installed, it would not be returnable as notated in our returns policy located at the following link: https://www.appliancepartspros.com/customerservice/returns.aspx Read More...
Morgan January 03, 2020 for Model Number WA48J7770AP/A2 I'm getting error code 8C, which i know is the mems sensor. I have purchased a new one but I don't know where the mems sensor is located. Where would the location be for my machine? Thanks
1 Answer Morgan, The MEMS sensor will be located on the right side, bottom of the outer tub, between the drain pump and the clutch motor, you'll need to raise and brace the front of the washer or lay it on it's back. You also want to check the wiring and connections as well " 8C- Error detected in the Mems PBA or data error detected. Check the wire connections. Replace if necessary. 1. Check the wire connections. 2. Replace the Mems PBA. 3. Main PBA wire connection error or PBA’s silver nano part malfunction. Replace if necessary." You also want to check the connections at the Sub PC board(conn.#52) for loose or damaged wires or connections. Read More...
Charles S December 07, 2019 for Model Number wa5ok8600av/aa Like where is the mem sensor is located on my Samsung active wash smart care vrt.is it in the front or back
1 Answer Charles, It appears that the mems sensor on this unit will be located at the bottom of the tub. Read More...
Joshua October 30, 2019 for Model Number WA52M7750AV/A4-00 I have a Samsung top load washer/dryer. A week ago the washer gave the code 8E and it would stay in the rinse and spin cycle. After doing some research I found it to be the MEMS sensor. I ordered it from you guys and placed it on the machine and nothing changed. I reassured the machine was level as well as the drum itself. What would you recommend my next coarse of action to be? Thanks
1 Answer Joshua, with the power cord unplugged from the wall, the wiring from the main control to the mems sensor will need to be tested for continuity. If the wires test good, then the most likely failure is going to be the main control DC92-02005A. Read More...
Steve October 26, 2019 for Model Number Kenmore Elite 592-49496 8E1 Error. All connections and wires look good. There appear to be two MEMS sensors atached to the drum. One in front and one at the back. The front says 150304 Back 150206. How do I know which one is causing the error? I can find two part numbers online. DC93-00278B DC93-00278A
1 Answer Steve, the mems sensor in front would be the most likely cause and is part number EAP4216273. Unfortunately, this is not a part that is carried as there are very limited parts that cross over to the US. Read More...
Arnel E October 06, 2019 Nd code (not draining). Replaced drain pump, cleaned all hoses from tub to the wall. Just before the rinse and spin cycle, the drain pump drains water, on then off then on then off then on until the water in the tub is drained. Then nothing.
1 Answer Arnel, With the pump working in one part of the cycle but not another then this would be a corrupt control board that would need to be replaced. Read More...